Instruction Manual; Technical Data - REMS Push Betriebsanleitung

g
Translation of the Original Instruction Manual
Fig. 1 – 2
1 High-pressure hose
2 Return valve
3 Tank/INOX tank
4 Pump lever
5 Pressure gauge
CAUTION
Failure to heed the following instructions can lead to severe
injuries.
Only use the tool for the intended purpose and under observance of the general
safety and accident prevention rules.
Untidiness in the work area can cause accidents.
b) Use the right tool. Do not use weak machines for heavy work. Do not use the
tool for a purpose for which it is not intended.
Slightly damaged parts must be checked carefully
for perfect and proper functioning every time before using the tool. Check whether
the moving parts work perfectly and do not jam or are damaged. All parts must
be mounted correctly and meet all conditions to ensure perfect operation of the
tool. Damaged parts must be properly repaired or changed by a recognised
d) Be careful. Pay attention to what you are doing. Work sensibly.
range. Renew worn tools in time.
f) Wear suitable work clothing. Do not wear loose clothing or jewellery as these
can get caught in moving parts. Rubber gloves and non-slip shoes are recom-
mended for working outdoors. Wear a hair net over long hair.
keep your balance at all times.
Keep the tools clean to work better and safer.
Follow the maintenance regulations and instructions. Keep handles dry and free
from grease and oil.
good lighting.
Do not let other persons touch your tools. Keep other
persons and especially children away from your work area.
for the intended function of the tool. The use of other insertion tools and
accessories can cause you injury.
nent safety regulations. Repairs may only be done by a recognised specialist or
instructed person with the use of genuine spare parts, otherwise the user could
safety reasons.
CAUTION
Failure to heed the following instructions can lead to severe
injuries.
So be very careful. Keep third parties away from the work area when working
with the device.
Damaged high-pressure hoses can burst and cause injury.
This ensures that the safety of the device is maintained.
an inclined, uneven surface, liquid can escape from the tank (3) or the device
can tip over.
alcohol, solvent, with the device. The fumes or liquids can ignite or explode.
Protect the device against frost. The device could be damaged.
Do not overload the device. Overloading can damage the device. There is a
risk of injury.
person. Otherwise there is a risk of operating errors and injuries.
the device when they are older than 16, when this is necessary for their training
and under the supervision of a trained operative.
A Hand pressure testing pump
B Installed lines
C Connecting line
D Pressure gauge
E Shut-off valve
F Shut-off valve upstream of installed
system
Wear safety glasses. Wear protective gloves.
Do not expose your tools to rain. Provide
There is a danger of accident.
If operated on
Apprentices may only operate
CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the opera ing manual before star ing
Environmentally friendly disposal
CE conformity mark

1. Technical Data

Use for the intended purpose
CAUTION
REMS Push and REMS Push INOX are designed for pressure and leak testing of
pipe systems and vessels. All other uses are not for the intended purpose and are
therefore prohibited.
NOTICE
Hand pressure testing pump, high-pressure hose, instruction manual
REMS Push
REMS Push INOX
Connection piece with pressure gauge and shut-off valve
Fine scaled pressure gauge
REMS CleanM
Capacity of the tank
pH value of the liquids
Dimensions REMS Push, REMS Push INOX
Weight REMS Push, REMS Push INOX
Hose connec ion
CAUTION
unauthorised access during pressure testing.
-
The hand pressure testing pump (A) is used for pressure and leak testing of
pipe systems (B), observe EN 806-4 standard and national regulations. To do
and also he shut-off valve (E) to the installed system. Close the shut-off valve
testing pump to the system being tested (hose connection ½"). Open the return
Bleed he installed system. Close the shut-off valve upstream of the installed
with the pump lever (4). In the case of major differences between the ambient
temperature and the water temperature a waiting period until these temperatures
are balanced is necessary. Close the shut-off valve (E) on the installed system.
open the return valve (2). Remove the high-pressure hose from the installed
system.
NOTICE
3. Maintenance
3.1. Maintenance
Grease the pump piston from time to time. Check high-pressure hose (1) and
seals for damage before every use. Do not use a damaged high-pressure hose
REMS CleanM machine cleaner (Art. No. 140119) or a mild soap and a damp
cloth. Do not use household cleaners. These often contain chemicals which
can damage the plas ic parts. Never use petrol, turpentine, thinner or similar
products for cleaning.
3.2. Inspection/Repair
g
115000
115001
115110
115045
140119
12 l
7 – 12
500 × 190 × 280 mm
6.9 kg
½"
Protect the area from
5