Cresta DTX500 Bedienungsanleitung Seite 44

Initial Initial Operation Operation
Initial Initial Operation Operation
• After inserting the batteries, the main unit will connect with the outdoor sensor by RF signal.
The RF signal symbol at the out area will flash.
This process takes about 3 minutes. Then the display shows the outdoor temperature
•
/humidity/wind speed/wind direction/rainfall, in case of failure of reception , pls press "␇" for
more than 3 seconds to receive again.
the automatic receiving of the DCF radio signal begins after 3 minutes of outdoor RF
•
reception.
This RCC reception process is going on,the flashing symbol "radio tower" appears in the
•
time display area at the same time.
• Once radio signal receiving is successful, the display shows the symbol "radio
tower" continuously, no flashing.
If, due to bad reception,or no RCC automatic time reception is possible, follow the steps below
manually.
Manual Manual time time set-up set-up
Manual Manual time time set-up set-up
12/24hour, 12/24hour, 12/24hour, 12/24hour, time time time zone,languages time zone,languages zone,languages zone,languages etc.
Press and hold key " " " " M M M M " " " " for 3 seconds.
• • • •
• The 12/24 hour flashing. Use "▲" and "▼" to select
Press " " " " M M M M " " " " to confirm.
• • • •
The display for the time zone is flashing. Use "▲" and "▼" to select the time zone
•
(-12 to +12).
Press " " " " M M M M " " " " to confirm.
• • • •
The DM/MD DM/MD flashing, Use "▲" and "▼" to select DM/MD DM/MD
•
• • • • Press " " " " M M M M " " " " to confirm.
• The display for the year is flashing. Use "▲" and "▼" to select the year.
Press " " " " M M M M " " " " to confirm.
• • • •
The display for the month is flashing. Use"▲ " and "▼" to select the month.
•
Press " " " " M M M M " " " " to confirm.
•
• The display for the date is flashing. Use "▲ " and "▼" to select the date.
Press " " " " M M M M " " " " to confirm.
•
The display for the hour is flashing. Use "▲ " and "▼" to select the hour.
•
Press " " " " M M M M " " " " to confirm.
•
• The display for the minutes is flashing. Use "▲ " and "▼" to select the minutes..
Press " " " " M M M M " " " " to confirm.
•
The language selection for the display of the weekdays is flashing. Use "▲" and "▼ " to
•
select the language.
Press " " " " M M M M " " " " to confirm
•
The C/F C/F for temperature flashing, Use "▲ " and "▼ " to select . C/F C/F
•
Press " " " " M M M M " " " " to confirm.
•
hpa/inhg hpa/inhg
• The hpa/inhg hpa/inhg for air pressure flashing, Use "▲" and "▼" to select .
Press " " " " M M M M " " " " to confirm.
•
The mm/inch mm/inch mm/inch for rainfall and kmh/mpg flashing, Use "▲" and "▼" to select . mm/inch
•
• • • • Press " " " " M M M M " " " " to confirm.
Please Please also also follow follow the the
(Please Please also also follow follow the the steps
etc. ) ) ) ) etc. etc.
steps steps steps to to to to choose choose choose some some
choose some some setting,
setting, setting, such such as as
setting, such such as as