Transport; Storage; Disposal And Recycling - Scheppach LBH3500P Original Bedienungsanleitung

Service information
With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Wearing parts*:Spark plug, air filter, fuel filter, collec-
tion bag
* may not be included in the scope of supply!
Spare parts and accessories can be obtained from
our service centre. To do this, scan the QR code on
the cover page.

12. Transport

ATTENTION!
Keep the hot silencer away from your body. There is
a risk of burns!
WARNING!
Unintended or unexpected start-up of the device can
result in serious injuries.
After the engine has cooled down, pull the spark
plug connector off the spark plug (see chapter 11.2.2
Spark plug maintenance).
Allow the engine to cool down before transporting or
loading to avoid burns and to prevent fire hazards.
When transporting over longer distances, completely
empty the fuel tank (see 11.3.1 Draining the fuel-oil
mixture).
Secure the device on the transport vehicle against
rolling, slipping or tipping over.

13. Storage

• Clean and maintain the device every time before
storage (see chapter "Cleaning and maintenance").
• Store the device in a safe, dry, frost-free, well-ven-
tilated place protected from the weather and out of
reach of children.
• Outdoor storage is not advisable. Also secure the
device from unauthorised access.
• Empty the fuel tank.
WARNING
Do not empty the fuel tank in enclosed areas, near
fire or when smoking. Petrol fumes can cause explo-
sions and fire.
• Start the engine and let it run until the remaining
petrol is used up.
WARNING
Store the device in a dry location, far away from po-
tential sources of ignition, such as furnaces, hot water
boilers with gas, gas dryers, etc. - Fire hazard!
If you store the device for longer than 30 days, it must
be prepared ahead of time. Otherwise, the remaining
fuel in the carburettor will evaporate and leave a rub-
bery sediment behind. This could make it difficult to
start and result in expensive repair work.
1. Slowly remove the fuel tank (22) cap (23) to re-
lease any pressure in the tank.
2. Carefully empty the fuel tank (22). Only empty the
tank outdoors or in well-ventilated rooms. Make
sure that no fuel gets into the soil (environmental
protection). Use a suitable surface.
3. Start the engine and let it run until it stops in order
to remove the fuel from the carburettor.
4. Allow the engine to cool down (approx. 5 minutes).
5. Remove the spark plug connector cover (24).
6. Remove the spark plug connector (30) from the
spark plug.
7. Remove the spark plug.
8. Add 1 teaspoon of clean 2-stroke oil through the
spark plug bore hole and into the combustion
chamber.
9. Pull the start pull cord (20) slowly several times to
coat the internal components.
10. Re-insert the spark plug.
Recommissioning
1. Remove the spark plug.
2. Pull the start pull cord (20) quickly to remove ex-
cess oil from the combustion chamber.
3. Clean the spark plug and check that the electrode
gap on the spark plug is correct is correctly set, or
insert a new spark plug with the correct electrode
gap.
4. Prepare the device for operation.

14. Disposal and recycling

The device is supplied in packaging to avoid
transport damages. This packaging is raw
material and can thus be used again or can
be reintegrated into the raw material cycle.
The device and its accessories are made
of different materials, such as metals and
plastics. Take defective components to special waste
disposal sites. Check with your specialist dealer or
municipal administration!
Fuels and oils
Fuel residues, oils and liquids used for cleaning must
be disposed of in an environmentally friendly manner!
Empty oil and fuel tanks must be disposed of in an
environmentally friendly manner.
Dispose of liquids and containers at appropriate col-
lection centres.
www.scheppach.com
GB | 35