Dust/Chip Extraction; Starting Operation - Bosch GSR 18V-45 Professional Originalbetriebsanleitung

LEDs
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Changing the tool (see figure A)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
The drill spindle is locked when the on/off switch (11) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation ➋. This will automatically lock the
drill chuck.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Bosch Power Tools
Capacity Operation
0−5 %

Starting Operation

Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Push the charged battery (7) into the base of the power tool
from the front until the battery is securely locked.
Capacity
Setting the rotational direction (see figure B)
80−100 %
Only operate the rotational direction switch (10)
u
60−80 %
when the power tool is not in use.
40−60 %
The rotational direction switch (10) is used to change the ro-
20−40 %
tational direction of the power tool. However, this is not pos-
5−20 %
sible while the on/off switch (11) is being pressed.
Right rotation: To drill and to drive in screws, press the
0−5 %
rotational direction switch (10) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (10) through to the
right stop.
Setting the operating mode
Drilling
Screwdriving
Impact drilling
Switching on/off
To start the power tool, press and hold the on/off switch
(11).
The LED (9) lights up when the on/off switch (11) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (11).
GSR 18V-45
Set the torque presetting ring (3) to the
"drilling" symbol.
GSB 18V-45
Set the operating mode presetting ring (4) to
the "drilling" symbol.
GSR 18V-45
Set the torque presetting ring (3) to the re-
quired torque.
GSB 18V-45
Set the operating mode presetting ring (4) to
the "screwdriving" symbol.
Set the torque presetting ring (3) to the re-
quired torque.
GSB 18V-45
Set the operating mode presetting ring (4) to
the "impact drilling" symbol.
1 609 92A 6GH | (20.12.2021)
English | 17