Reinigung - steute GFI Extreme Montage- Und Anschlussanleitung

GFI Extreme / GFSI Extreme
//
Montage- und Anschlussanleitung / Fußschalter
Mounting and wiring instructions / Foot switch
Instructions de montage et de câblage / Pédale de commande
Istruzioni di montaggio e collegamento / Interruttore a pedale
Instruções de montagem e instalação / Pedal de comando
Инструкция по монтажу и подключению / Ножной выключатель
Deutsch (Originalbetriebsanleitung)
Instandhaltung, Wartung, Reparatur
=
GEFAHR
Spannungsführende Teile. Stromschlaggefahr!
Beschädigte und defekte Geräte nicht reparieren,
sondern ersetzen. Alternativ: Defekte Geräte durch
Fachpersonal in Abstimmung mit steute und mit
steute-Ersatzteilen reparieren.
Bei rauen Betriebsbedingungen empfehlen wir eine regelmäßige
Wartung mit folgenden Schritten:
1. Prüfen der Pedale auf Leichtgängigkeit.
2. Entfernen von Schmutz.
3. Prüfen der Leitungseinführung und -anschlüsse.

Reinigung

=
GEFAHR
Spannungsführende Teile. Stromschlaggefahr!
Schutzart beachten.
- Bei feuchter Reinigung: Wasser oder milde, nicht-scheuernde,
nicht-kratzende Reinigungsmittel verwenden.
- Keine aggressiven Reinigungs- oder Lösungsmittel verwenden.
Entsorgung
- Nationale, lokale und gesetzliche Bestimmungen zur Entsorgung
beachten.
- Materialien getrennt dem Recycling zuführen.
English
Use of the mounting and wiring instructions
Target group: authorised and qualified staff.
All actions described in these instructions may only be performed by
qualified persons who have been trained and authorised by the
operating company.
1. Read and understand these mounting and wiring instructions.
2. Comply with the valid occupational safety and accident prevention
regulations.
3. Install and operate the device.
Selection and installation of devices and their integration in control
systems demand qualified knowledge of all the relevant laws, as well
as the normative requirements of the machine manufacturer.
In case of doubt, the German language version of these instructions
shall prevail.
Scope of delivery
1 device, mounting and wiring instructions, carton.
Safety information
=
In this document, the warning triangle is used
together with a signal word to indicate a
hazardous situation.
The signal words have the following meanings:
NOTICE
indicates a situation which may
result in material damage.
WARNING
indicates a situation which may
result in serious injury or death.
Intended use
The device is particularly suitable for industrial use due to its robust
design. The manufacturer accepts no liability for improper use.
Installation, mounting, dismantling
=
DANGER
Live parts. Electric shock hazard! Connecting and
disconnecting only to be performed by qualified and
authorised personnel. Connecting and disconnect-
ing only in zero potential state.
NOTICE
Untight if mounted at low temperatures. Mount
carefully at low temperatures.
Wire the foot switch according to the specified wire colours/terminal
labelling. Contact symbols shown refer to an unactuated switch.
Application and operation
=
DANGER
Live parts. Electric shock hazard! Protective cover
over contacts must be intact.
CAUTION
In case of overloaded contacts too high operation
temperatures. Risk of burns! For short-circuit
protection use appropriate fuse size (see
technical data).
- Use device only within the permitted electrical load limits (see
technical data).
2 / 16
CAUTION
indicates a situation which may
result in minor or moderate
injury.
DANGER
indicates a situation which will
result in serious injury or death.