Vielen Dank dafür, dass Sie sich für ein Wintec-Produkt entschieden haben. Dieses Handfunkgerät wurde nach modernsten Technologien entwickelt. Bitte lesen Sie diese Bedienungsanleitung vor der Benutzung aufmerksam durch und bewahren Sie sie sicher auf. Sicherheitshinweis Das Funkgerät darf nicht in explosionsgefährdeter Umgebung benutzt wer- den.
Tasten und Anschlüsse Antennenbuchse (SMA weiblich) Der MR-200 ist für die Verwendung mit Antennen vorgesehen, die auf allen Betriebsfrequenzen eine Impedanz von etwa 50 Ω haben. Die Antenne sollte immer angeschlossen sein, wenn man den Transceiver einschaltet. USB-Buchse (für Updates) Nur für Firmware-Updates zu benutzen.
Seite 5
Einen Kanal nach oben bzw. Auswahlmöglichkeit im Set-Modus. ▼DOWN-Taste Einen Kanal nach unten bzw. Auswahlmöglichkeit im Set-Modus. Displaybeleuchtung / EIN/AUS Kurz drücken: Beleuchtung ein/aus. Lange drücken: Transceiver ein/aus. SET-Taste Kurz drücken: Aufrufen des Set-Modus. Lange drücken: Zurück zur Normalbedienung. Display Anzeige des aktuellen Status des MR-200.
Display RSSI / Sendeleistungspegel Anzeige der Empfangssignalstärke bzw. des Sendeleistungspegels. CTCSS / Lautsprecher (ein / aus) Zeigt an, ob der aktuelle Kanal eine CTCSS-Einstellung hat oder nicht. Wenn das Symbol blinkt und der Lautsprecher eingeschal- tet ist, hat der Kanal keine CTCSS-Einstellung. Niedrige Sendeleistung Zeigt an, dass für den aktuellen Kanal die niedrige Sendeleis- tungsstufe gewählt ist.
Grundbedienung Wenn man den MR-200 das erste Mal mit dem Bordnetz des Fahrzeugs ver- bindet, wird der Transceiver automatisch eingeschaltet. Einschalten des Transceivers An der Haupteinheit oder am Bedienteil die Power-Taste lange drücken, worauf die Anzeige im Display erscheint und man einen Startton hört. Beim Einstellen der Lautstärke ist Vorsicht geboten, weil hohe Lautstärken das...
Pegel 0 bis Pegel 7 SOUND Sound ein/aus ON / OFF Auto Power OFF 30 / 60 / 120 min Time-Out-Timer 30 / 60 / 90 / 180 / 360 sec Reset des MR-200 auf die voreinge- RESET NO / YES stellten Werte...
* Der Anschluss externer Audiogeräte erfolgt über einen speziellen Eingang mit 3,5-mm-Buchse. Für die 3,5-mm-Kabel möglichst Originalkabel verwen- den, um Störungen zu vermeiden. Installation des MR-200 am Motorrad Anschluss der Betriebsspannung (+) Positive Zündspannung, Akku usw. (–) Negativ (Masse bzw. Metallteile des Motorrads) Wenden Sie sich an einen Fachbetrieb, falls Sie die Anschlüsse selbst nicht finden.
Funkgerät mit Velcro-Band am Fahrzeug befestigen. Installation des Helm-Headsets 【Wichtig! 】Das Mikrofon möglichst vor oder mindestens nahe am Mund an- bringen, damit die Verständigung gut ist. Mit dem „Innenleben“ des Helms vertraut machen. Haupt-Lautsprecher so befestigen, dass er sich mög- lichst nahe am rechten Ohr befindet.
Wenn die Lautsprecher und das Mikrofon befestigt sind, führt man das Anschlusskabel auf die Außenseite des Helms. Anbringen des Boom-Mikrofons Das Boom-Mikrofon muss sich für optimale Verständi- gung möglichst nahe am Mund befinden. 【Wichtig! 】Das Boom-Mikrofon ist ein Richtmikrofon, sodass es in der richtigen Lage angebracht werden muss, siehe Abbildung oben.
Technische Daten Allgemein PMR446 Frequenzbereich Anzahl der Kanäle CTCSS Squelch-System Modulationsart 16 Ω 0,5 W Lautsprecherimpedanz –30 °C bis +80 °C Betriebstemperaturbereich 184 g (Haupteinheit) Gewicht 69 mm × 80 mm × 28 mm (H×B×T) Abmessungen Sender Sendeleistung 500 mW Stromaufnahme unter 500 mA Empfänger...
Thank you for purchasing Wintec products. Based on the innovative technology in this ever-changing environment, we have been developed many wireless products that have attract more consumers’ attentions. We sincerely appreciate your interest for our products, and we suggest you read the instruction carefully.
Controls and Switches Antenna Jack (SMA Female) The MR-200 is designed for use with antenna presenting an impedance of near 50 Ohms at all operating frequencies. The antenna should be connected whenever the transceiver is turned on. USB Jack (Factory update) Only for factory update.
Seite 19
Channel down and at setting manual mode is selector. Backlight / Power Shot press: Backlight on / off Press and hold: Power on / off Shot press: In to the setting manual mode. Press and hold: Back main manual. Displays the current status of MR-200.
LCD Icons Rssi / Tx Power Level Instruction the Received signal strength or Transmitted signal strength. CTCSS / Speaker (on / off) Indicates that the channel is set CTCSS or not, when this icon is displayed. The display indicates that the channel has not set CTCSS when the icon flashes to indicate when the speaker turned on.
Basic Operating Instructions Started using MR-200, first lap will host the power cord to power the vehicle, which will automatically turn on the MR-200. Turn On the Radio Press and hold main unit or driver Control Box Power button, then the screen will light up and you hear the startup tone, adjust the volume to use radios , pay attention ! ! The volume is too large will likely damage your hearing.
Turn on this function when radio signal with other signal(GPS, Navigation...) RF PRI Radio volume priority come in then MR-200 will be automation adjust down other signal to priority listen radio signal. Squelch level setting Level 3 Level 0~ Level 7...
Seite 25
Main cable (Drive) Drive control (Power and Volume) PTT extension cable Helmets cable Helmets headset Power cable Antenna mount RF cable with connector (SMA-M) Antenna...
This product is built-in driving passenger intercom function, with cable kit as below. Main cable Passenger Control Helmets Headset (Passenger) (PTT and Volume) *This product is built-in external audio input, you can use 3.5mm audio terminals. 3.5mm audio cable please use the original cables to avoid noise interference. Products Installation Diagram Power connection diagram (+) Positive Ignition power supply or battery, etc.
Use Velcro Tape fix radio on the vehicle. Helmet Headset Installation Diagram 【Important! 】Please install location] microphone mounted on the front of the mouth to get a better reception. Please removable helmet lining. Please depending on the actual structure of the main speakers stuffed helmet placed or affixed to the helmet to the right ear position Please helmet lined structure according to another...
Seite 28
When helmets internal speakers and microphone are fixed, please setup the QQ line of fittings fixed to the outside of the helmet. Install Boom Microphone Keep boom microphone fixed to the helmet, and then adjusted to the mouth in front of the microphone. 【Important! 】Due to the use of this product] directional microphone, so make sure it is correct sides of the microphone, as shown, the microphone has to be...
Specifications General PMR446 Frequency Range Channel Number CTCSS Sub-Audio Modulation Type 16Ω 0.5W Speaker Impedance -30 ∼ +80℃ Operating Temperature 184g (Main body) Weight 69(H)×80(W)×28(D) mm Size Transmitter RF Output Power 500mW Current Less than 500mA Receiver Better than 0.2uV @ 12db SIAND Receive Sensitivity Less than 50mA Receive Current...