Bosch GWS 18V-10 Professional Originalbetriebsanleitung Seite 33

Fitting
®
Inserting the Bluetooth Low Energy
Module GCY 42
®
Note: The Bluetooth Low Energy Module GCY 42 is avail-
able as an accessory with GWS 18V-10 PC power tools; it is
included in the scope of delivery for GWS 18V-10 SC and
GWS 18V-10 PSC power tools.
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
Fitting Protective Equipment
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard
(15) onto the holder on the
power tool until the coding
cams of the protective guard
are aligned with the holder.
When doing so, press and
hold the unlocking lever (1).
Press the protective guard
(15) onto the spindle collar
until the shoulder of the pro-
tective guard is sitting on the
flange of the power tool and
rotate the protective guard
until it audibly clicks into
place.
Adjust the position of the protective guard (15) to meet the
requirements of the operation. To do this, push the unlock-
ing lever (1) upward and rotate the protective guard (15)
into the required position.
Always position the protective guard (15) such that
u
the two cams on the unlocking lever (1) engage in the
corresponding openings on the protective guard (15).
Adjust the protective guard (15) such that sparking in
u
the direction of the operator is prevented.
The protective guard (15) must only be adjustable
u
while the unlocking lever (1) is actuated. Otherwise,
the power tool must not be used any more under any
circumstances and must be sent to the after-sales ser-
vice.
Note: The coding cams on the protective guard (15) ensure
that only a protective guard that is suitable for the power
tool can be fitted.
Bosch Power Tools
Extraction guard for sanding
For low-dust grinding of paints, lacquers and plastics in con-
junction with carbide grinding heads (19), you can use the
extraction guard (14). The extraction guard (14) is not suit-
able for machining metal.
A suitable Bosch dust extractor can be connected to the ex-
traction guard (14). To do so, insert the vacuum hose with
dust extraction adapter into the provided receiving connec-
tion of the extraction guard.
Protective guard for cutting
For cutting, always use the protective guard for
u
cutting (16) or the protective guard for grinding (15)
together with the cover for cutting (17).
Provide sufficient dust extraction when cutting stone.
u
The protective guard for cutting (16) is fitted in the same
way as the protective guard for grinding (15).
Metal cover for cutting
Fit the metal cover for cutting (17) on the protective guard
for grinding (15) (see figure A): Swivel the tool retainer back
(➊). Attach the cover (17) to the protective guard for
grinding (15) (➋). Press the tool retainer firmly into place
on the protective guard (15) (➌).
To remove the cover (see figure B), press the button on the
tool retainer (➊) and swivel it back (➋). Remove the
cover (17) from the protective guard (15) (➌).
Plastic cover for cutting
Attach the plastic cover for cutting (17) to the protective
guard for grinding (15) (see figure C). The cover (17) aud-
ibly and visually engages on the protective guard (15).
To remove the cover (see figure D), unlock the cover (17) on
the left- or right-hand side of the protective guard (15) (➊)
and remove the cover (➋).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (29) is fit-
ted in the same way as the protective guard for grinding
(15).
Hand guard
Always fit the hand guard (28) when working with the
u
rubber sanding pad (30) or with the cup brush/conical
brush/diamond annular cutter.
Attach the hand guard (28) to the auxiliary handle (11)/
(10).
Standard auxiliary handle/low-vibration auxiliary handle
Screw the auxiliary handle (11)/(10) on the right or left of
the machine head depending on the working method.
Do not operate your power tool without the auxiliary
u
handle (11)/(10).
Do not continue to use the power tool if the auxiliary
u
handle (11)/(10) is damaged. Do not make any altera-
tions to the auxiliary handle (11)/(10).
English | 33
The low-vibration auxiliary
handle (10) reduces vibra-
tion, enabling the tool to be
1 609 92A 769 | (24.02.2022)