Pairing/Connecting Your Handsfree With Bluetooth Device; Erase All Paired Records - Anycom HCC-250 Bedienungsanleitung

2.4 Pairing/Connecting your Handsfree with Bluetooth Device

2.4.1 Pairing your HCC-250 with Bluetooth mobile phone (or other device)
Before making and answering calls, you must pair your HCC-250 and phone. Paring sets up a unique relationship between your Car-Kit and your
mobile phone. The mobile phone will memorize the HCC-250`s unique ID (or passkey). This ensures that a unique and encrypted wireless link between
your Car-Kit and mobile phone will be used during calls.
Detailed operation procedures are as follows:
1. Place your HCC-250 close to your Bluetooth enabled mobile phone, and ensure your Car-Kit is power off, your mobile phone is power on
2. Press and hold button
indicate that the Car-Kit has successfully entered the paring mode
3. Following your phone user guide to active Bluetooth device search on the phone side, on your phone screen you will see a list of Bluetooth equipment
found by the phone at the end of the searching process.
4. Select this Bluetooth Car-Kit HCC-250 from the list and initiate pairing following handset's on-screen prompts.
5. Continue to follow on-screen prompts to enter passkey "0000" and confirm to pair the HCC-250 with your mobile phone. Once the pairing procedure is
completed, you will hear a connecting tone, and then Blue LED gives 3 quick blinks per 2 seconds. It indicates that the Car-Kit device and the mobile
phone are paired and connected.
Note:
If pairing is successful, Car-Kit`s Red LED is off. The Blue LED gives 3 quick blinks per 2 seconds. If your mobile phone shows that paring is failed and the Car-Kit
is still in the paring mode, you need to go back to above steps 3-5 to repeat the paring process.
Your Car-Kit will remain in the pairing mode for about 2 minutes. If paring cannot be finished within 2 minutes, the HCC-250 will enter into the standby
mode (without Bluetooth connection in this case). You need to turn the Car-Kit off and then repeat the above steps 2-5 to restart the pairing process.

2.4.2 Erase all Paired Records

This Car-Kit can be paired with up to 8 Bluetooth devices. When in the paring mode, press and hold – button for at least 3 seconds will allow you to erase all
paired bluetooth device profiles stored in the Car-Kit. The Car-Kit will then quit from the pairing mode. The Blue LED will give 1 blink per 3 seconds.
2.4.3 Connecting/Disconnecting your HCC-250 Car-Kit with a Bluetooth Device
When the Car-Kit communicates with a Bluetooth equipment thru Handsfree Profile, the Bluetooth connection between two equipments shall be established in
advance. If two Bluetooth equipments have been paired once, you can simply reconnect them.
Connecting your HCC-250 with a Bluetooth mobile phone
Initiating a request from either the Car-Kit or the mobile phone can set up Bluetooth connection. The detailed operations are as follows:
1. Initiating connection request from the Car-Kit: Place the Car-Kit close to the Bluetooth mobile phone and then press button
2. Initiating connection request from the Bluetooth mobile phone: Place the Car-Kit close to the Bluetooth mobile phone and then follow the phone`s user
guide to find the Car-Kit and send connection request.
After connecting, you will hear a connecting tone, and then Blue LED gives 3 quick blinks per 2 seconds
Disconnecting your HCC-250 from your Bluetooth mobile phone:
When the Car-Kit is connected with Bluetooth mobile phone (or in the connected mode), you can disconnect them as follows:
1. Pressing and holding button
2. Following the mobile phone`s user guide and initiating disconnection from the phone side.
After disconnecting, you will hear a disconnecting tone, and then Blue LED gives 1 blink per 3 seconds.
for at least 6 seconds until the Blue and Red LEDs alternate continuously. You will hear 2 power-up tones and a pairing tone to
for at least 3 seconds.
Page 5
HCC-250 - English
.