Ego Power+ STX3800 Übersetzung Der Originalanleitung Seite 9

Cutting: used for cutting the grass that is difficult to
reach using a normal mower.
NOTICE: The tool is to be used only for its prescribed
purpose. Any other use, for example hedge trimming,
is deemed to be a case of misuse.
ATTACHING/DETACHING THE BATTERY CABLE
Use only with EGO's battery packs and chargers
listed in Fig.A2
Fully charge before first use.
To Install Battery cable (Fig.M)
Align of plug with of line trimmer. Insert the plug into
the machine until the green seal completely disappeared
into the socket.
To Remove
Release the battery cord from the mounting groove and pull
out the plug from the line trimmer.
STARTING/STOPPING THE LINE TRIMMER (Fig. N)
To Start
Push the lock-off Lever to position "ON", push the locking
tongue forward then depress the switch trigger. The trigger
is stepless speed adjusting. The more you pull up the
trigger, the higher speed it is.
N-1 Lock-off Lever
N-2 Locking tongue
To Stop
Release the switch trigger and push the lock-off button
back to position "OFF".
WARNING: Always unplug the battery connector
from the socket during work breaks and after finishing
work.
USING THE LINE TRIMMER
WARNING: To avoid serious personal injury, wear
goggles or safety glasses at all times when operating
this unit. Wear a face mask or dust mask in dusty
locations.
Clear the area to be cut before each use. Remove all
objects, such as rocks, broken glass, nails, wire, or line,
that can be thrown or become entangled in the cutting
attachment. Clear the area of children, bystanders,
and pets. At a minimum, keep all children, bystanders
and pets at least 15m away; there still may be risk to
bystanders from thrown objects. Bystanders should be
N-3 Switch Trigger
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — STX3800
encouraged to wear eye protection. If you are approached,
stop the motor and cutting attachment immediately.
Before each use, check for damage/worn parts
Check the bump head, guard and loop handle and replace
the parts that are cracked, warped, bent, or damaged in
any away.
The line-cutting blade on the edge of the guard can
dull over time. It is recommended that you periodically
sharpen it with a file or replace it with a new blade.
After each use, clean the trimmer.
CAUTION:
Obstructions in the vents will prevent
the air from flowing into the motor housing and result in
overheating or damaged of the motor.
◾
Use only mild soap and a damp cloth to clean the tool.
Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
◾
Keep air vents in the motor housing from debris at all
times.
WARNING: Never use water for cleaning your
trimmer. Avoid using solvents when cleaning plastic
parts. Most plastics are susceptible to damage from
various types of commercial solvents. Use clean cloths
to remove dirt, dust, oil, grease, etc.
ADJUSTING CUTTING LINE LENGTH
The trimmer head allows the operator to release more
cutting line without stopping the motor. As line becomes
frayed or worn, additional line can be released by lightly
tapping the bump knob on the ground while operating the
trimmer.
NOTICE:
Line release will become more difficult if the
cutting line becomes too short.
WARNING: Do not remove or alter the line-
cutting blade assembly. Excessive line length will
cause the motor to overheat and may result in serious
personal injury.
Line replacement
NOTICE: Always use the recommended nylon cutting
line with a diameter that does not exceed 3.0 mm.
Using line other than that specified may cause the line
trimmer to overheat or become damaged
WARNING: Never use metal-reinforced line,
wire, or rope, etc. These can break off and become
dangerous projectiles.
1. Remove the power plug from the string trimmer.
2. Remove the remaining cutting line, if necessary.
EN
.
9