Herunterladen Inhalt Inhalt Diese Seite drucken

General Power Tool Safety Warnings - Makita rp0900 Betriebsanleitung

Oberfräse
Vorschau ausblenden Andere Handbücher für rp0900:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 16
ENGLISH (Original instructions)
1.
Stopper pole
2.
Screw
3.
Lock lever
4.
Depth pointer
5.
Adjusting hex bolt
6.
Stopper block
7.
Switch trigger
8.
Workpiece
SPECIFICATIONS
Collet chuck capacity
Plunge capacity
No load speed (min
Overall height
• Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
ROUTER SAFETY WARNINGS
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
6
Explanation of general view
9.
Bit revolving direction
10. View from the top of the tool
11. Feed direction
12. Straight guide
13. Guide bar
14. Clamp screw
15. Base
16. Templet guide
Model
-1
)
Net weight
Safety class
3. Wear hearing protection during extended period
ENE010-1
of operation.
4. Handle the bits very carefully.
5. Check the bit carefully for cracks or damage
ENF002-1
before operation. Replace cracked or damaged bit
immediately.
6. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
7. Hold the tool firmly with both hands.
8. Keep hands away from rotating parts.
9. Make sure the bit is not contacting the workpiece
before the switch is turned on.
10. Before using the tool on an actual workpiece, let it
run for a while. Watch for vibration or wobbling
GEA010-1
that could indicate improperly installed bit.
11. Be careful of the bit rotating direction and the feed
direction.
12. Do not leave the tool running. Operate the tool
only when hand-held.
13. Always switch off and wait for the bit to come to a
complete stop before removing the tool from
workpiece.
14. Do not touch the bit immediately after operation; it
may be extremely hot and could burn your skin.
15. Do not smear the tool base carelessly with
GEB018-2
thinner, gasoline, oil or the like. They may cause
cracks in the tool base.
16. Draw attention to the need to use cutters of the
correct shank diameter and which are suitable for
the speed of the tool.
17. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
18. Always use the correct dust mask/respirator for
the material and application you are working with.
17. Bit
18. Templet
19. Distance (X)
20. Outside diameter of the templet
guide
21. Dust nozzle
22. Thumb screw
RP0900
6mm, 1/4", 8 mm and/or 3/8"
0 - 35 mm
27,000
217 mm
2.7 kg
/II

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis