AVENLI 12015 Bedienungsanleitung Seite 6

RF3-21-GB
PART3-SITE SELECTION
WARNING:
Pools installed on inadequately level surfaces are subject to leak-
ing, forming irregularities, or collapse, which can result in property damage or
serious injury for those in or around the pool area!
WARNING:
Do not use sand during setup process. If it appears that there is a
need for use of a "leveling agent", then your set-up site is likely unsuitable. FAIL-
URE TO OBEY THIS WARNING MAY RESULT IN SERIOUS PERSONAL INJURY.
CAUTION:
Please choose your set-up area carefully, as lawn and other desir-
able vegetation underneath the ground cloth(If applicable) will die. Furthermore,
try to avoid setting the ground cloth(If applicable)in areas prone to aggressive
plant and weed species, as they may grow through the ground cloth(If applica-
ble).
CAUTION:
The pool must be accessible to a 110 or 230-volt AC outlet pro-
tected by a Ground Fault Circuit Interrupter (GFCI). The pool should be set no
closer than 2 m. to the power source, but no further than the length of the filter
pump cord. Under no circumstances should an extension cord be used to extend
the range of the connection.
It is absolutely essential to select a suitable site for your pool BEFORE attempting to
fill it with any water. Please select a set-up site which strictly conforms to the following
guidelines:
Guide1.
Ensure that the area is firm, flat (no bumps or mounds of earth) and extremely level, with a grade not exceeding
3° of slope at any point in the set-up area.
Guide2.
Make sure that the area you have selected to set-up the pool is completely free of sticks, stones, sharp objects or
other foreign debris.
Guide3.
Select an area that is not directly underneath overhead power lines or trees. Additionally, make sure that the pool
set-up area does not contain underground utility pipes, lines, or cables or any kind.
Guide4.
If a ground cloth is provided with your pool kit, its use is highly recommended. The ground cloth will help protect
the pool liner from damage due to weed growth, sharp objects, and debris.
Guide5.
If at all possible, choose an open location on your property that is exposed to direct sunlight. This will help to
warm your pool.
Flat,Level Ground-CORRECT
10
Bumpy,Sloping Ground-INCORRECT
+3°
PART4-SET UP THE POOL
IMPORTANT:
Do not start assembly if any pieces are missing. For replacement pieces call the Consumer Service
telephone number in your area.
The number of persons required for installation: 2 adult at least.
Total installation time except the time for site preparation and water filling :
30 minutes for size Ф10'×30"/Ф12'×30"
45 minutes for size Ф14'x33"/Ф15'x33"
Step1. ACCOUNT FOR ALL PARTS.
Remove all the parts from the carton(s) and place them on the ground in the location where they are to be assembled
Check each part according to "PART REFERENCE" .Make sure all the pieces to be assembled are accounted for.
Step2. INSTALL DRAIN VALVES COVER AND STOPPER
Make sure that outer drain plug is inserted into the outer drain cap and drain valve cover is screwed on tightly.Plug the con-
nection holes with the stoppers. (The out drain plug changes according to different size of pool.)
STOPPER Drain Vavle Cover
Step3. INSTALL HORIZONTAL BEAM
Step4. INSTALL T-JOINT(FOR TYPE B)
RF3-21-GB
Out Drain Plug A Out Drain Plug B
1. Use the connection end of the T-Joint to connect
the adjacent horizontal tubes.
2. Insert the Pin into the hole of connected horizon-
tal tube and T-Joint firmly.
3. Install the vertical leg cap onto the vertical leg.
4. Insert the vertical leg into the T-Joint through the
belt.
TIP: If you can't find the hole on the horizontal
tube or vertical leg please rotate the tubes until the
pin meets the hole.
11