Troubleshooting Guide; Warranty; Technical Data; Vibration Value - Kärcher HGE 36-60 Battery Originalbetriebsanleitung

4. Sharpen the exposed side of all blade teeth with a
file.
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device does not start
up
The device stops during
operation

Warranty

The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Technical data

Device performance data
Working voltage of the battery
Idling speed (normal setting)
Cut material diameter (max.)
Determined values in acc. with EN 60745-1,
EN 60745-2-15
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L + K uncer-
WA
tainty
WA
Front handle hand-arm vibration
value
Rear handle hand-arm vibration
value
Uncertainty K
Dimensions and weights
Cutting length
Weight (without battery pack)
Subject to technical modifications.
18

Troubleshooting guide

Cause
Battery pack is not inserted correctly.
Battery pack is empty
Battery pack is defective.
Blade blocked with cutting material.
The battery has overheated
Motor has overheated
HGE 36-
60 Bat-
tery
V 36
/min 350-
1240 ±
10%
mm 26
dB(A) 78,1
dB(A) 3,4
dB(A) 93
2
m/s 0,3
2
m/s 0,3
2
m/s 1,5
mm 600
kg 3,45
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
 Push the battery pack into the mounting
until it latches into place.
 Charge the battery pack.
 Replace the battery pack.
 Remove cutting material from the blade.
 Stop working and allow the battery to cool
down to normal battery temperature.
 Stop working and allow the motor to cool
down.

Vibration value

WARNING
The specified vibration value was measured using a
standard test procedure and may be used to compare
devices.
The specified vibration value may be used in a provi-
sional assessment of the load.
Depending on the way the device is used, the vibration
emission can deviate from the specified overall value
during the current use of the device.
Device with a hand-arm vibration value >
2.5 m/s² (see chapter Technical Data in the
operating instructions)
CAUTION
for several hours can lead to numbness.
gloves to protect your hands.
from work.

EU Declaration of Conformity

We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
culation by us. This declaration is invalidated by any
changes made to the machine that are not approved by
us.
Product: Hedge trimmer
Type: HGE 36-60 Battery
Currently applicable EU Directives
2000/14/EC (+2005/88/EC)
2014/30/EU
2006/42/EC (+2009/127/EC)
2011/65/EU
Harmonised standards used
EN 50581: 2012
EN 55014-1: 2017
EN 55014-2: 2015
EN 60745-1:2009+A11:2010
EN 60745-2-15:2009+A1:2010
Conformity evaluation procedure used
2000/14/EC and amended by 2005/88/EC: Appendix V
Sound power level dB(A)
Measured:89.1
English
●
Uninterrupted use of the device
●
Wear warm
●
Take regular breaks