Before Starting The Equipment - EINHELL GE-CM 43 Li M Originalbetriebsanleitung

residual risks cannot be eliminated. The fol-
lowing hazards may arise in connection with
the equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is applied.
Warning!
This equipment generates an electromag-
netic fi eld during operation. Under certain
circumstances this fi eld may actively or pas-
sively impede medical implants. To reduce
the risk of serious or fatal injuries, we recom-
mend persons with medical implants to con-
sult their doctor and the manufacturer of the
medical implant prior to using the equipment.

5. Before starting the equipment

The lawn mower is delivered partly assembled.
The push bar and the grass basket must be as-
sembled before using the lawn mower. Follow the
instructions step by step and refer to the pictures
when assembling.
Mounting the push bar (Fig. 3 to 7).
Insert the push bar holder (Fig. 2/Item 3) into
the handlebar mount and secure with the quick
clamping function (Fig. 2/Item 11) (Fig. 3). The
top push bar (Fig. 1/Item 2) must be pushed onto
the push bar holders (Fig. 2/Item 3) and secured
as shown above in Fig. 4. Then attach the power
cable to the push bar (Fig. 5/Item 13) using the
cable clips (Fig. 2/Item 13). Now you can select
the push bar height in three stages (Fig. 6/Item A).
Note!
The handle height may be adjusted only within
the marked range.
•
Press in the long handle and secure in the
desired position using the quick clamping
function (Fig. 6/Item 11)
Warning!
Always set the identical handle height on both
sides.
•
Use the cable clips to align the cable to the
long handle (Fig. 5/Item 13)
Fitting the grass box (see Figs. 7 to 9)
First plug the lower part of the housing (Fig. 2/
Item 15) and the right part of the housing (Fig. 2/
Anl_GE_CM_43_Li_M_SPK13.indb 22 Anl_GE_CM_43_Li_M_SPK13.indb 22
GB
Item 18) together as shown in Fig. 7. Then plug
the top part of the housing (Fig. 2/Item 17) onto
the previously assembled parts (Fig. 8).Before
you fi t the grass basket you must ensure that the
motor is switched off and the blade is not rotating.
Lift the ejector fl ap (Fig. 9/Item 7) with one hand.
With the other hand, hold the grass basket by the
handle and hook it in from above (Fig. 9).
Filling level indicator of the grass collector
The grass box is equipped with a fi lling level in-
dicator (Fig. 2/Item 16). which is opened by the
airfl ow that the lawn mower generates during ope-
ration. If the fl ap closes during mowing, the grass
collecting device is full and must be emptied. To
ensure the proper functioning of the fi lling level
indicator, the holes under the fl ap must always be
kept clean and passable.
Adjusting the cutting height
Caution!
Adjust the cutting height only when the machine
has been switched off and the safety plug has
been pulled out.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
safety plug.
The cutting height is adjusted as follows (see Fig.
11):
1. Push the lever (A) outwards.
2. Set the lever (B) to the desired cutting height.
3. Release the lever (A) and check that it is se-
curely seated in the lock.
Reading off the cutting height
The cutting height can be set between 25-75 mm
in 6 intervals, and can be read off on the scale
(Fig. 11/C).
Using the mulching adapter (Fig. 10)
In mulching mode the cuttings are shredded in
the enclosed mower housing and then spread
back onto the lawn. It is not necessary to gather
and dispose of the grass.
Notice! Mulching is only possible if the lawn is
relatively short.
- 22 -
13.10.2021 12:48:39 13.10.2021 12:48:39