Weighing Function (Weight Measurement Only); Enter Of Personal Data; Body Analysis - ADE BA 833 Sybille Bedienungsanleitung

4. Weighing function (weight measurement only)

1. Switch on the scale by using the step-on-function. Just step on the scale. Remain
stationary on the weighing platform and do not hold you tight. After a few seconds,
your weight will be displayed.
2. After weighing, step off the scale. The scale will switch off automatically after a few
seconds.
5. Programming / Enter of personal data
Before first time use your personal data like gender (female or male), body height and
age must be programmed and saved under selected locations 1 – 12 (up to 12 persons).
The enter keys are located right hand beside the display. To enter your personal data
please utilise the buttons: ON/SET (on and save button),
button) and follow the particular points:
1. Place the scale on a table and press the ON/SET-button.
2. The display indicates flashing, " Code 1" . To select your
personal location (1– 12) press the  or ‚ button. After
the selection of your personal location press the ON/SET-
button to save the reading.
3. After you' ve selected your personal location (e.g. 5), the
symbol for gender starts to flash. To select the requested
gender (female / male), press the  or ‚ button. After the
selection of your gender press the ON/SET-button to
save the reading.
4. after you have selected your gender (e.g. female), the
symbol for body height starts to flash (default 165 cm). To
enter your height press the  or ‚ button. After the
selection for your height press the ON/SET-button to save
the reading.
5. After you' ve selected your body height (e.g. 166 cm), the
symbol for age starts to flash (default age 25). To enter
your age press the  or ‚ button. After the selection of
your age press the ON/SET-button to save the reading.
After input completion tap with your hand or foot shortly on the scale or press the
START-button. The display indicates the signal " 0.0 kg" . Afterwards the scale
automatically powers off.
 (plus button), ‚
4
To enter personal data of further persons please repeat the steps listed below.

6. Body Analysis

An analysis is only possible in bare feet. Your personal data must be entered first (please
see page 4).
1. Switch on the scale by using the step-on-function. For this, tap with your foot shortly on
the centre of the scale. The display indicates the signal " 0.0 kg" . Press the ON/SET-
button and select with the  or ‚ button your personal location.
2. On the display, you can see your personal data (age, body height, and gender). Now
press the START-button. At the first time measurement the display indicates the signal
„ 0.0" kg. When you once used the scale, the display indicates primarily the readings of
your last measurement. This function allows you to follow the changes between your
(minus
measurements. As soon as the display shows „ 0.0" the scale is prepared for the
measurement.
3. Carefully in bare feet step on the stainless steel strips on the right and left side of the
weighing platform and remain stationary while the measurement is now taking place.
4. At first, your weight will be indicated on the display. Shortly after, while the analysis is
taking place, on the display the signal " ooo" starts to move. After completion of the
measurement, your measured values will be shown as follows:
a. Your body fat % and beneath as barcode an evaluation of your body fat status
(lllli – too lean / llll llll
your body water % and your weight kg.
b. Your muscle mass %, your bone mass % and your daily calorie requirement (basal
metabolic rate).
EXAMPLE:
Body Fat / Body Water / Weight
5. Afterwards your measured values will be shown in changes successively 3 times. After
this, the scale switches off automatically.
i i i
– lean / llll llll llll – normal / llll llll llll llll – fat / llll llll llll llll llll
Muscle Mass / Bone Mass / D. C. R.
5
i
– too fat),