Bosch AKE 30 S Bedienungsanleitung Seite 19

Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
If devices are provided for the connection of
dust extraction and collection facilities, en-
sure these are connected and properly used.
Use of these devices can reduce dust related
hazards.
Power tool use and care
Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
Disconnect the plug from the power source
before making any adjustments, changing ac-
cessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of start-
ing the power tool accidentally.
Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous in
the hands of untrained users.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many acci-
dents are caused by poorly maintained power
tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits
etc., in accordance with these instructions
and in the manner intended for the particular
type of power tool, taking into account the
working conditions and the work to be per-
formed. Use of the power tool for operations dif-
ferent from those intended could result in a haz-
ardous situation.
19 • F 016 L70 540 • TMS • 29.01.09
Service
Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of the
power tool is maintained.
Chain Saw Safety Warnings:
Keep all parts of the body away from the saw
chain when the motor is operating. Before you
start the saw, make sure the saw chain is not
contacting anything. A moment of inattention
while operating chain saws may cause entangle-
ment of your clothing or body with the saw chain.
Always hold the chain saw with your right
hand on the rear handle and your left hand on
the front handle. Holding the chain saw with a
reserved hand configuration increases the risk of
personal injury and should never be done.
Wear safety glasses and hearing protection.
Further protective equipment for head, hand,
legs and feet is recommend. Adequate protec-
tive clothing will reduce personal injury by flying
debris or accidental contact with saw chain.
Do not operate a chain saw in a tree. Operation
of a chain saw in a tree, may result in personal in-
jury.
Always keep proper footing and operate the
chain saw only when standing on fixed, se-
cure and level surface. Slippery or unstable sur-
faces such as ladders may cause a loss of bal-
ance or control of the chain saw.
When cutting a limb that is under tension be
alert for spring back. When the tension in the
wood fibres is released the spring loaded limb
may strike the operator and/or throw the chain
saw out of control.
Use extreme caution when cutting brush and
saplings. The slender material may catch the
saw chain and be whipped toward you or pull you
off balance.
Carry the chain saw by the front handle with
the saw chain stopped and the guide bar
pointing to the rear. When transporting or
storing the chain saw always fit the guide bar
cover. Proper handling of the chain saw will re-
duce the likelihood of accidental contact with the
moving saw chain.
Follow instructions for lubricating, chain ten-
sioning and changing accessories. Improperly
tensioned or lubricated chain may either break or
increase the chance for kickback.
Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery caus-
ing loss of control.
English - 2