Herunterladen Inhalt Inhalt Diese Seite drucken

Makita DFL020F Betriebsanleitung Seite 8

Vorschau ausblenden Andere Handbücher für DFL020F:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 53
Function
Motor failure detection
Double-hitting detection
Maintenance alarm
Alarm for unavailable
data communication
(with the tool in connec-
tion with PC)
Indication that data com-
munication is available
(with the tool in connec-
tion with PC)
Adjusting the fastening torque
When you wish to drive machine screws, hex bolts,
etc. with the predetermined torque, adjust the fastening
torque as follows.
1.
Install the battery cartridge.
2.
Open the change plate by hand so that you can
see a hole.
► Fig.7: 1. Change plate
3.
Pull the switch trigger and release it so that the
adjust ring rotates and the hole becomes visible. And
then remove the battery cartridge.
4.
Use an optional adjust grip to adjust the fastening
torque. Insert the pin of the adjust grip into the hole
in the front of the tool. And then, turn the adjust grip
clockwise to set a greater fastening torque, and coun-
terclockwise to set a smaller fastening torque. Use the
yellow line as a rough guide.
► Fig.8: 1. Adjust grip 2. Hole for adjust grip 3. Yellow
line
5.
Insert the battery cartridge and be sure that a
fastening torque has been set up by using a fastening
torque tester.
6.
Close the change plate by hand securely.
Adjusting no-load speed and
revolution angle etc.
You can adjust the no-load speed, number of turn, etc.
of the tool with your computer. Install the application
software in your computer and connect it to the tool with
an USB cable.
► Fig.9: 1. USB cable 2. USB cover 3. USB port
NOTICE:
Make sure that the USB cover closed
when fastening.
NOTE: For the application software, please contact
Makita sales representative.
Status of the tool
Motor failure has been
Flickers in red and green
detected. At this time,
alternatively.
tool does not work.
When the operator
Lights up in red.
starts to re-fasten an
already-fastened screw,
the tool detect it and
stops.
A maintenance time has
Flickers in yellow.
come according to your
preset number of screws
driven.
Data cannot be
Flickers in yellow.
exchanged between the
tool and PC in spite of
the connection.
The tool is connected to
Flickers in green.
PC and data communi-
cation is available.
Status of the LED indicator/beeper
LED indicator
A series of short beeps
A long beep
ASSEMBLY
CAUTION:
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Selecting correct socket
There are different types of sockets for some models
depending on applications. Choose and install a correct
socket for your application.
Installing or removing socket
► Fig.10: 1. Socket 2. Hole 3. Pin
To install the socket, push it onto the square drive of the
tool with one hand by depressing a pin on the square
drive with another hand until it locks into place. To
remove the socket, simply pull it off depressing the pin
on the square drive.
CAUTION:
the socket is properly locked onto the square
drive. Incomplete attachment of the socket may
cause injury.
Installing or removing driver bit/
socket bit
Country specific
► Fig.11
Use only driver bit/socket bit that has inserting portion
shown in the figure. Do not use any other driver bit/
socket bit.
8 ENGLISH
Action to be taken
Beeper
Ask your local Makita
Service Center for repair.
Reset the alarm with the
application software.
Restart the application
software and re-connect
the USB cable.
Always be sure that the tool is
Before operation, make sure that

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Dfl063f

Inhaltsverzeichnis