Technical Data - AEG WS 24-180 Originalbetriebsanleitung

TECHNICAL DATA

Rated input ..................................................................................
Output ..........................................................................................
Max. no-load speed .....................................................................
Grinding disk diameter.................................................................
Thread of work spindle ...............................................................
Weight without cable ...................................................................
Measured values determined according to EN 60745.Typically,
the A-weighted noise levels of the
tool are:
Sound pressure level ...........................................
Sound power level ...............................................
Wear ear protection!
according to EN 60745:
Surface grinding: vibration emission value a .............................
h
............................................................................
Disk sanding vibration emission value a ....................................
h
............................................................................
For other applications, e.g. Abrasive Cutting-Off Operations or
Wire Brushing other vibration values could occure.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
brochure. Failure to follow the warnings and instructions may
Brushing or Abrasive Cutting-Off Operations:
Failure to follow all
serious injury.
Operations for which the
power tool was not designed may create a hazard and cause
personal injury.
because the accessory can be attached to your power tool, it
does not assure safe operation.
Accessories running faster than their rated speed can break
Incorrectly sized accessories cannot be
adequately guarded or controlled.
Accessories with arbour holes that do not match the
mounting hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
inspect the accessory such as abrasive wheels for chips
20 ENGLISH
WS 24-180 WS 24-230
WS 24-180 E WS 24-230 E
............... 2400 W ..................2400 W .................... 2400 W
............... 1560 W ..................1560 W .................... 1560 W
............... 8500 min -1 ...............6600 min -1 ................ 6600 min
................. 180 mm ..................230 mm ................... 230 mm
............... M 14 ......................M 14 ....................... M 14
.................. 5,0 kg .....................5,1 kg ...................... 5,3 kg
................... 94 .................93 ..................
................. 105 ...............104 ...............
2 2
..................... 6 m/s .....................6 m/s ................... 5,2 m/s
.................. 1,5 m/s 2 ..................1,5 m/s 2 ................... 1,5 m/s
............... < 2,5 m/s 2 ...............< 2,5 m/s 2 ................ < 2,5 m/s
.................. 1,5 m/s 2 ..................1,5 m/s 2 ................... 1,5 m/s
Damaged
accessories will normally break apart during this test time.
The eye protection must be capable of
generated by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
Fragments of workpiece or of a broken accessory may
Just
Cutting accessory
contacting a „live" wire may make exposed metal parts of the
power tool „live" and shock the operator.
lose control, the cord may be cut or snagged and your hand or
arm may be pulled into the spinning accessory.
The spinning accessory may grab the
surface and pull the power tool out of your control.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
will draw the dust inside the housing and excessive accumulation
of powdered metal may cause electrical hazards.
Sparks could ignite these materials.
water or other liquid coolants may result in electrocution or shock.
WS 24-230 GVX
WS 24-230 EGVX
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which
-1 in turn causes the uncontrolled power tool to be forced in the
direction opposite of the accessory's rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing the
wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction of
the wheel's movement at the point of pinching. Abrasive
wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
2
2
2
2
The operator can control torque reactions or kickback forces, if
proper precautions are taken.
Accessory may kickback over your hand.
direction opposite to the wheel's movement at the point of
snagging.
sharp edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
Such blades create frequent kickback and
loss of control.
Cutting-Off Operations:
Wheels for which the power tool was not
designed cannot be adequately guarded and are unsafe.
protect operator from broken wheel fragments and accidental
contact with wheel.
Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these wheels may
cause them to shatter.
of wheel breakage. Flanges for cut-off wheels may be different
If you
Wheel intended for larger power tool is not suitable for the
higher speed of a smaller tool and may burst.
Off Operations:
Overstressing the wheel increases the loading and
The motor's fan
susceptibility to twisting or binding of the wheel in the cut and
the possibility of kickback or wheel breakage.
When the wheel, at the point of operation, is
moving away from your body, the possible kickback may propel
Using
the spinning wheel and the power tool directly at you.
Investigate and take corrective action to eliminate the
cause of wheel binding.
The wheel may bind, walk up or kickback if the power tool
is restarted in the workpiece.
tend to sag under their own weight. Supports must be placed
under the workpiece near the line of cut and near the edge of
the workpiece on both sides of the wheel.
may cut gas or water pipes, electrical wiring or objects that can
cause kickback.
sanding pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
Kickback will propel the tool in
a) Be aware that wire bristles are thrown by the brush
Corners,
bristles can easily penetrate light clothing and/or skin.
due to work load and centrifugal forces.
Appliances used at many different locations including open air
should be connected via a residual current device of 30 mA or
less.
Dust and splinters must not be removed while the machine is
running.
Only plug-in when machine is switched off.
Never reach into the danger area of the tool when it is running.
Always use the auxiliary handle.
The guard helps to
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine in
Always use and store the grinding disks according to the
manufacturer's instructions.
no combustible materials should be located in the vicinity
Proper
from the workpiece come into contact with you.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work
with the machine.
steady. Never lead the workpiece to the grinding disk with your
hand.
contamination can build up on the inside of the angle grinder.
For safety reasons, in such conditions the inside should be
cleaned thoroughly of metal deposits and a motor circuit-
breaker must be connected in series. If the motor circuit-
breaker trips the machine must be sent for repair.
ensure that the thread in the wheel is long enough to accept
the spindle length.
For cutting or separating use a closed protection cap, available
as an accessory.
Large workpieces
The protruding wheel
Larger sanding paper extending beyond the
The wire
Wire wheel or brush may expand in diameter
ENGLISH 21