Work Safety; Safety Instructions For Operation; Personal Protective Equipment - Husqvarna CL400i Bedienungsanweisung

• Do not change this product or use it if it is possible
that it has been changed by others.

Work safety

WARNING:
instructions that follow before you use the
product.
• Use the product to put boundary wire and guide wire
for robotic lawn mowers into the ground. Do not use
the product for other tasks.
• Use personal protective equipment. Refer to
Personal protective equipment on page 12 .
• Make sure that you know how to stop the motor
quickly in an emergency.
• Do not operate the product in rain or wet conditions.
The risk of electrical shock increases if water enters
the product.
• Do not operate the product unless the drill and
all covers are attached correctly. An incorrectly
attached drill can come loose and cause injury.
• Remove objects such as branches, twigs and stones
from the work area before you use the product.
• Objects that hit against the cable laying equipment
can eject and cause damage to persons and objects.
Keep bystanders and animals at a safe distance
from the product.
• Never use the product in bad weather such as fog,
rain, strong winds, intense cold and risk of lightning.
To use the product in bad weather or in moist or wet
locations is tiring. Bad weather can cause dangerous
conditions, such as slippery surfaces.
• Look out for persons, objects and situations that can
prevent safe operation of the product.
• Look out for obstacles, such as roots, stones, twigs,
pits and ditches. Long grass can hide obstacles.
• Do not use the product on ground that slopes more
than 15°.
• Exercise extreme caution when changing direction
on slopes. Operate the product across the face of
slopes. Do not move up and down.
• Be careful when you go near hidden corners and
objects that prevent a clear view.
• Make sure that the drill does not hit objects such as
stones and roots. This can do damage to the drill
and bend the motor shaft. A bent motor shaft causes
heavy vibration and a very high risk that the drill
becomes loose.
• If the drill hits an object or if vibrations occur,
stop the product immediately. Stop the motor, pull
up the safety key and remove the battery. Wait
until moving parts stop. Examine the product for
damages. Tighten loose parts. Repair damages and
replace damaged parts. Let an approved service
agent do the repair.
• Do not attach the drill operation bail permanently to
the handle when the motor is started.
• Put the product on a stable, flat surface and start it.
12
Read the warning
• Always stay behind the product when you operate it.
• Let all the wheels stay on the ground and keep 2
hands on the handle when you operate the product.
• Keep your hands and feet away from the rotating
drill.
• Do not tilt the product when you start the motor or
during operation of the product.
• Be careful when you pull the product rearward.
• Do not lift up the product when the motor is started.
If you must lift the product, first stop the motor, pull
up the safety key and remove the battery.
• Do not walk rearward when you operate the product.
• Release the drill operation bail to stop the drill when
it is necessary to tilt the product for transportation.
• Do not run with the product when the motor is
started. Always walk when you operate the product.
• Stop the motor before you change the cable laying
depth. Do not make adjustments with the motor
started.
• Do not let the product stay out of view with the motor
started. Stop the motor and make sure that the drill
does not rotate.
• The vibrations in the product during operation can
be different from the declared vibration value in
Technical data on page 21 . The difference is
caused by variations in how the product is used.
If you operate the product frequently or for long
periods of time, take breaks regularly to prevent
injury from vibrations.

Safety instructions for operation

Read the instructions that follow before you use the
product.
• Make sure that the cable on the cable guide is intact.
• Make sure that the tube in the feeding fin is intact.
Replace the tube if it is worn or damaged.
(Fig. 14)
• Make sure that the edge around the hole is not
sharp or damaged. Replace the cable guide if it is
damaged.
• Make sure that all screws are tightened.
• Make sure that all levers are in neutral position.

Personal protective equipment

WARNING:
instructions that follow before you use the
product.
• Personal protective equipment cannot fully prevent
injury but it decreases the degree of injury if an
accident does occur. Let your dealer help you select
the right equipment.
• Use heavy-duty slip-resistant boots or shoes. Do not
use open shoes or go with bare feet.
• Use heavy, long pants.
Read the warning
1698 - 001 - 21.01.2022