Installation - Mohlenhoff Alpha Smartware BSS 21001 N2-Serie Schnellinstallationsanleitung

Radio frequency 868.3 and 869.525
MHz SRD band
Number of actua- max. 4 x 2 and 2 x
tors 1
Protection type IP 20
Connection cable 0,2 ... 1,5 m²
(cross section)
Wire stripping 8 ... 9 mm
length of connec-
tion terminals
typ. free-field radio 270 m
range
Max. nominal load 24 W
of all actuators
Fuse 5 x 20 mm, T4AH
Max. switchable 1 A
power
4 Installation
Installing the device
See Fig. 3 [& 3]
Connecting the device
See Fig. 4 [& 4]
Close cover
See Fig. 5 [& 4]
5 Commissioning
First Open function
See Fig. 6 [& 5]
1. Establish the power supply to the base station.
2. All heating zones are activated consecutively for ten
minutes each in order to unlock the first-open function
of the connected actuators.
Coupling devices - Pairing
See Fig. 7 [& 5]
Long press means pressing >3 sec / Short press means
pressing <1 sec
1a) Teaching room control units to heating
zones
1. Press and hold the button Pairing [B] to activate the
pairing mode: The LED Pairing flashes slowly.
ð If instead the Error LED flashes red, all heating zones
are already occupied.
868.3 and 869.525
MHz SRD band
max. 4 x 2 and 6 x
1
IP 20
0,2 ... 1,5 m²
2. Briefly press the Pairing button [B] repeatedly until the
8 ... 9 mm
3. Briefly press the Clear [A] button to confirm the previ-
270 m
24 W
5 x 20 mm, T4AH
4. Press and hold the Pairing [B] button to start the pairing
1 A
5. Briefly press the rotary pushbutton of the room control
6. Press the Pairing [B] button on the base station briefly to
7. Briefly press the rotary pushbutton of the room control
1b) Teaching a room control unit to
additional heating zones
Perform the following steps to pair an already paired room
control unit with additional heating zones.
Start the pairing process on the base station and select the
desired heating zone(s), see 1a), steps 1 to 4.
1. Press and hold the rotary pushbutton of the desired
2. Briefly press the rotary pushbutton of the room control
3. Press the Pairing [B] button on the base station briefly
4. Briefly press the rotary pushbutton of the room control
Unpairing room control unit from paired
heating zones – Cancel pairing
Long press means pressing >3 sec / Short press means
pressing <1 sec
ü To disconnect the room control units, perform the pair-
1. Press and hold the button Clear [A] to start decoupling:
2. Press the button Clear [A] briefly and repeatedly until
ð The LEDs of all already coupled heating zones light
up permanently
ð The LEDs of all heating zones available for pairing
flash slowly
ð Press and hold the Clear button [A] to exit the pair-
ing mode.
desired heating zone is selected.
ð The LED of the selected heating zone flashes quickly
ously selected heating zone for the pairing process: The
LED of the selected heating zone lights up permanently
ð To assign additional heating zones: Repeat steps 2
and 3.
process for the previously selected heating zones: The
LED Pairing flashes quickly
unit: The room control unit displays PAI Join
complete the process: The room control unit displays
PAI done
unit to end the pairing process
room control unit: Set PAIr is displayed
unit: PAI Join is displayed
to complete the process: Pai done is displayed.
unit to end the pairing process
ing steps using the [A] and [B] keys in opposite.
The LED Clear and all coupled heating zones flash slowly
the desired heating zone(s) is/are selected.

Installation

DEU
ENG
FRA
NDL
ITA
ESP
DAN
NOR
FIN
SWE
POL
RUS
11