Commissioning; Set Up; Electrical Connection; Polish (Only For Modules With Polish Dispenser) - Heute Ellipse Originalbetriebsanleitung

Commissioning

Set up

Remove transport safeguard and any provided polish (not automati-
cally a component of the machine) between the rubber mat and
brushes.
Only operate the machine in enclosed rooms. The machine must
be protected against splashing water and the effects of water. The
machine must be set up on a horizontal surface so that it cannot
slip. To achieve a safe stance of the machine, floor unevenness must
be compensated (e.g. by placing suitable rubber strips under the
machine. For the Ellipse and Quadro models instability is more likely
to occur due to the pillar shape.

Electrical connection

The machine is delivered ready for connection. The factory specifica-
tion requires that the power be connected via a standardized and
fused ground contact socket outlet. Voltage and current must agree
with the specifications on the rating plate (110 volt or 230 volt).

Polish (only for modules with polish dispenser)

For models with polish dispenser the use of polish is possible as an
option. We recommend the use of our HEUTE shoe polish, because
we can guarantee trouble-free function for this polish in conjunc-
tion with our machines. The polish is available separately and is not
automatically part of the scope of delivery.
Filling the polish dispenser
(Only for modules with polish dispenser)
All shoe shine machines with polish dispenser are always delivered
with an empty polish dispenser. To fill the polish dispenser, tilt
the machine to the rear, so that you can easily remove the polish
dispenser holder from the holder rail by unscrewing it a quarter turn.
Take the valve neck bottle out of the holder, unscrew the twist-off
cap and fill the valve neck bottle with polish. After filling the bottle
with polish, ensure that the cap is firmly closed and that the valve
is functioning properly. Fit the filled valve bottle back into the holder
and turn the holder with the bottle by pressing it upward into the
bayonet closure in such a manner that the view window is pointing to
the front. Test whether the polish dispenser works properly with the
ball valve, by lightly pressing the tip of your shoe against the polish
valve from below. After the polish has settled in the container, polish
must be applied to the leather via the valve.
Use of the polish bottle for model Polifix 4
After opening the lockable housing flap, pull off the connector that
sits on the hose and screw it onto the thread of the open bottle of
polish (original HEUTE accessory). Then turn the bottle of polish in
the horizontal position, so that the opening of the hose connector
that is screwed onto the bottle of polish fits into the hose opening.
Fix the bottle of polish in place, upside down (opening downward),
in the provided clamp holder. Thereafter, we recommend using a nail
or similar item to punch a hole in the bottom of the plastic bottle
(which is now pointing upward), to prevent a vacuum from occurring
in the bottle through dispensing of the polish. This measure ideally
ensures the proper flow of polish.
16
All manuals and user guides at all-guides.com

Assembly instructions - holding rod Cosmo 3 plus

1 | Scope of delivery
1 x shoe shine Cosmo 3 plus,
1 x holding rod, pre-mounted, 1 x Allen wrench,
1 x fastening screw 8 x 60mm,
1 x fastening screw 8 x 45mm, 1 x spacer sleeve
2 | Mounting the holding rod
Place the housing and rod in position.
Fit the plug connectors of the housing and rod together (1).
3 | Mounting the holding rod
Set up the rod, insert the lower screw (2), slide on the sleeve and
tighten the screw hand tight. Screw in the upper
screw (3) and tighten it hand tight. Attention:
Ensure that the cable is not pinched in the rod!
4 | Mounting the holding rod
Align the rod (4), first tighten the lower screw (5), then tighten
the upper screw (6).
!
#
@
$
^
%