KIKKA BOO ANGELE Gebrauchsanweisung Seite 9

WARNING
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THEM FOR LATER REFERENCE. THE SAFETY OF YOUR CHILD COULD BE PUT AT RISK IF YOU DO NOT
FOLLOW THESE INSTRUCTIONS.
• Leaving the baby without care may cause a danger .
• Use the harness when the baby begins to sit at his own.
• Do not use an additional mattress in the product.
• Before use be sure that the assembling mechanisms are blocked
• Always use the crotch belt together with the help belt.
• Every load handing on the handle affects its stability.
• This product is not designated to go roller blades or to run. WARNING: This stroller is indented to bear only one baby.
• This stroller is designated for the babies up to 0-36 months and weight 22kg.
• Do not leave the stroller with a baby on the slope, even if the brake islocked.
• Do not use the stroller, if any component is damaged.
• During the assembling and disassembling the stroller, be sure that the baby is at the safe distance.
• Making any adjustments, make sure that the movable parts are not close to the baby' s body.
• Always lock the brake when stops. Always lock the brake when put or carry a child.
• Maximum load of basket is 3 kg.
• Maximum load of bag is 2 kg.
• Every bag or other load handing on the handle affects its stability.
• Only the original parts, confirmed by the producer should be used in this product.
• Driving on the pavement or any other step the front axle should be lifted.
• Do not drive the stroller through the stairs
• The stroller should be kept away from babies
PARTS LIST
1. CANOPY; 2. SEAT; 3. FRAME; 4. BUMPER; 5. FRONT WHEELS; 6. REAR WHEELS;
ASSEMBLY
1.OPEN THE STROLLER
1a. Unlock the stroller by pushing the lock plastic to the out side of the stroller.
1b. Lift the handle up as figure1b.
1c. When the stroller is opened as figure1c, you should hear click sounds on both side of the stroller, please examine if the stroller is locked in safety position before you use it.
2. ASSEMBLE/DISASSEMBLE FRONT WHEELS
2a. To assemble the front wheels: Take one side of front wheels, insert the vertical shaft into the plastic hole on the wheel seat as figure 2a, until it is locked, install the other
side of the front wheel in the same way.
2b. Lock and rotate the front wheels: Put up the front wheel lock the front wheel can only go in one direction,put down the front wheel lock the front wheel can rotate in 360
degrees.
2c.To disassemble the front wheels: press the small metal pins as arrow "push", at the same time use your hand to pull out the front wheel as arrow 2 to finish disassemble.
3. ASSEMBLE/DISASSEMBLE REAR WHEELS
3a.To assemble the rear wheels: Take one side of rear wheels, Insert the rear axle into the plastic hole as figure 3a, until it is locked, install the other side of the rear wheel in
the same way.
3b.To disassemble the rear wheels: Pull the rear wheel express iron as red arrow, remove the rear wheel in the direction of white arrow then finish the disassemble.
4. Brake the stroller. Step down the brake pedal to brake the stroller, lift up the pedal to release the brake as figure 4a.
WARNING!Always lock the brake when put or carry a child ke the stroller
5.ASSEMBLE THE SEAT
Assemble the seat as figure 5(back to mother), you should hear a "click" sounds on both side to make sure the seat is locked in safety position. Push the unlock plastic on both
sides of the seat to take off the seat.
To reverse the seat in different direction (face to mother) in same way.
6. ASSEMBLE THE BUMPER
6a. Insert the bumper on both sides of the seat as gure 6a.
6b. Press the unlock button on both sides of the bumper at the same time pull out the bumper to take o the bumper.
6c. You can rotate the bumper in any direction.
Note: please make sure to lock the bumper in place when you heard a "click"sound.
7. ASSEMBLE THE CANOPY. Insert the canopy plastic into the seat as gure 7a.
8. ADJUSTED THE FOOTREST. Press the button as red arrow in the gure 8a to adjust the footrest in 3 position.
9. OPEN AND FOLD THE CANOPY. Extend or fold the canopy as gure 9.
10. ADJUSTED THE BACKREST. Lift up the button as red arrow in the gure10a to adjust the backrest to be in 3 position(sleeping or seat) as gure10b.
11. REVERSIBLE SEAT. Pull out the button and lift up the seat as gure 11a, then assemble the seat in opposite direction as gure11b, insert the seat in the frame to nish the
assemble.
ENGLISH