Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Danger!
12. The mains voltage must agree with the voltage
printed on the type plate.
13. Do not start the machine by bypassing electrical
circuits.
14. The mains cable must not
•
be damaged by being driven over, crushed,
yanked etc.
•
it is dangerous to drive over it when the
machine is in operation.
15. Regularly check the mains cable for damage.
16. Do not use the machine if the mains cable is
not in perfect condition.
17. When using or replacing the mains cable or
extension cables, do not use types that differ
from the manufacturer's original parts.
18. The connectors on mains and extension cables
must be at least splash-proof.
19. The plug on the connecting cable must be in-
serted into a socket that accords with regula-
tions.
20. Always disconnect the mains cable from the
power network before carrying out any cleaning,
servicing or maintenance work.
21. Always use suitable extension cables.
22. Only connect to a power network that is fitted
with leakage current protection equipment.
23. Only persons who are familiar with the machine
and who have been instructed in the possible
hazards may operate, service or repair it.
24. Remove all jewellery when working close to
electrical components.
25. Only use original replacement and accessory
parts. No liability is accepted for similar parts
from other manufacturers.
26. When performing cleaning and servicing work,
ensure that authoritative regulations applicable
to the particular location regarding the correct
handling of oils, fats, acids, alkalis, fuels and
other similar agents are obeyed.
27. Observe the regulations applicable to your
location when disposing of old machines or their
components.
28. Do not clean the machine with a high-pressure
cleaner.
1. Preparing the Machine
Attaching and removing accessories.
1.
Attaching Accessories
•
Unplug
•
Bring control handle into a vertical position
•
Tilt machine backwards
•
Fit accessory manually by turning to the left
402 VARIO
•
Cleaning, shampooing
= switch in position "I" at 165 min
•
Polishing, spray cleaning
= switch in position "II" at 330 min
2.
Removing accessories
•
Unplug
•
Tilt machine backwards
•
Remove accessory manually by turning to
the right
2. Correct working position
1.
Adjusting the control handle
•
•
•
3. Switching on/off
1.
The built-in "dead-man's" switch prevents the
machine from being switched on when the con-
trol handle is vertical.
2.
Starting the Machine:
•
•
3.
Switch off
•
•
•
4. Using the Machine
1.
Lightly grip the handles of the control handle in
both hands
•
•
•
5. Working Technique
1.
Begin as far away as you can from the socket
or door
2.
Work backwards
3.
Steadily work one track forwards and back
4.
Work so that the tracks overlap by about 1/3
6. Fitting the spray system
1.
Undo the spray system's locking screws
2.
Place it on the control handle underneath the
cable holder
3.
Point the spray nozzle towards the rear
4.
Attach the cable to the lever
5.
Tighten the locking screws
7. Fitting the dust extractor
1. Mount the vacuum unit on the control handle
-1
2. Insert the vacuum hose
3. Insert cable into the control bar
4. Fit the vacuum ring
-1
9
Undo the locking device
Select the working position
Fix the locking device
Caution!
Only start the machine when the control
handle is locked.
Possible only with tilted control handle
Push the switch outwards with the index
finger – press and hold
Release the switch
Machine switches off
Bring control handle into a vertical position
Caution!
Take care of the mains cable
Start machine
Push the control handle gently downwards
= the machine runs to the left
Lift the control handle gently upwards = the
machine runs to the right
Werbung
