Interline 57100105 Bedienungsanleitung Seite 8

EN
This is the case when:
Ø The device has visible damage
Ø The device no longer appears funcional
Ø After long periods of storage in poor
conditions
If the power cord or other parts of this equip-
ment are damaged, they have to be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid dan-
ger.
Damage during delivery
Your filter system has been carefully and professionally packed for
delivery. Please check to ensure that the package is undamaged and
that all parts are in the box. If you purchased this product on order and
the product was shipped to you, ensure that delivery is
Damage to product as a result of shipping is not the responsibility of
the supplier and must be immediately reported to the shipper.
shipper assumes the liability for damages during delivery, the supplier
is not responsible for it.
Implied Warranty
The manufacturer warranties safe operation and reliability only under
the following conditions:
Ø The filter system is installed and operated according to the
assembly and operating instructions.
Ø Only original replacement parts are used (consumable parts
do not fall under the warranty).
Expendable parts do not fall under the warranty. These include:
Ø All O-rings
Ø Pressure gauge
Ø Mechanical seal, complete
Resultant Damages
We cannot be responsible for damages to the product if the product
is not used in accordance with the instructions provided.
Technical Data:
PUMP Flow (Q)
MAX Operating Pressure
Filtration Area
Rated Voltage 230V 1N~ AC 50Hz
Power
Protection Class
Max. ambient tempera-
ture
Sand Volume
complete.
25 L 50 L
8.5 m³/h – 0,4 bar 9.5m³/h – 0,4
bar
1,5 bar 1,5 bar
0,13 m² 0,13 m²
230V 1N~ AC
50Hz
450 Watt 550 Watt
IP X5 IP X5
35 °C 35 °C
15~16 kg 25 kg
Unpacking your filter system
Carefully remove the product and all component parts from the box.
Cross reference all parts in the box with the parts list reference chart
to make certain all parts are present before beginning assembly.
NOTE: Some parts may be located within the filter tank. To access
these parts you must remove the tank cover.
Refer to Appendix A for a complete EXPLODED VIEW PARTS
DIAGRAM
Power source Instructions
Install the filter system at least 3.50 meters
away from the edge of the swimming pool.
The filter pump can be connected to a
grounded electric supply with an alternating
voltage of 230 V and 50 HZ and must be
protected by a differential switch (RCD)
with a sensitivity not above 30 mA. To
The
avoid electric shock, power cord extensions
should not be used.
Filter- Pump Assembly (Picture 1 – 5)
1. Water Pump – Base Plate Assembly
a) Secure water pump to the base plate
mounting hardware. Orient as
2. Pump Fittings Assembly
a) Screw the 1¼"-1½" hose connector
ter pump. Ensure that the O-ring "A" is installed between the port
and the connector.
b) Remove the threaded ring (Collar) on
pump.
c) Place O-ring "B" in the grove around the hair and lint strainer basket.
d) Place the transparent hair & lint strainer cover
screw the threaded ring (Collar) back on securely over the cover.
e) Insert O-ring "C"
transparent hair & lint strainer cover.
Place the base plate and pump in the location where the Pump-Filter
System will be located for normal operation and within reach of the
pool filter and return hoses but with a sufficient safety margin from
the edge of the pool
Attach the filter tank to the base plate as shown.The feet on the bottom
of the filter tank fit within the holes provided on the base plate
Insert the tank separator plate inside the main tank in the guides pro-
vided.
Filling sand chamber with sand (Picture 6)
with the provided pump
shown.
into the center port of the wa-
the outer opening of the
in place and then
(1 1/4") inside the outward facing opening of the
Page 8 of 22