AVS Electronics STARLINK 4G Allgemeines Installationshandbuch Seite 27

PARAMETERS PROGRAMMING
Programming of Starlink 4G, no matter if used as telephone interface or as telephone dialler, can be made either via PC by use of software XWIN
through the dedicated extension, or entering various parameters into the Sim Card.
The steps which follow are referred to the personalization of the parameters, opportunely programming the Sim Card Phonebook.
In order to do so, it is necessary to move the Sim Card into a mobile phone, program the necessary setting and then insert the card in
the GSM module.
PARAMETERS PROGRAMMING VIA SIM CARD
In order to enable the various functions, it is necessary to enter the parameters managing them in the Main Sim, (SIM A), whilst it is possible to
enter, if necessary, only the parameter concerning the "Number for Credit Verification" in the Secondary Sim (SIM B), (see chapter "PERSONA-
LIZATION OPERATORS NUMBERS").
Programming of basic parameters:
N000 To enter new data in the programming
X000 If N000 is present, it carries out an eeprom reset before entering
the data available in the Sim Card
In order to memorize the parameters programmed, it is necessary to insert the value N000 into the Main Sim Card, it adds the new values
into the Starlink 4G memory and maintains the existing ones, if any. If you wish to cancel all existing parameters before entering new data, it is
necessary to memorize not only the value N000 into the Main Sim Card, but also the value X000 which carries out an EEPROM reset.
For the procedure of data entering, both value N000 and value X000 are automatically cancelled on the Main Sim Card.
PROGRAMMING OF LANGUAGE:
Starlink 4G allows to set the language for SMS and vocal messages sending.
It is programmed by default for use of the Italian language; to change language, it is necessary to memorize a name having L000 () as
description and a telephone number of one figure corresponding to the chosen language.
L000 Number saved
0 or Nothing
1
2
3
PROGRAMMING OF SPECIAL FUNCTIONS:
In order to enable the various special functions, it is necessary to memorize a name having as description R000 (
Phonebook, associated to a 1 to 10 figures "Telephone Number" corresponding to the special functions themselves
R000 NO PRESENCE of parameter
0 Management of left-over credit on Main Sim Card (SIM A)
ENABLED
1 Activation of the Open Collector 1 output by vocal call in RTC or
by command SMS of one of the numbers memorized as User in
the Sim Card Phonebook
2 Activation of the Open Collector 2 output by vocal call or command
SMS of one of the numbers memorized as User in the Sim Card
Phonebook
3 Secondary Sim Card (SIM B) NOT PRESENT
4 Management of left-over credit ON secondary Sim Card (SIM B)
ENABLED
5 Working with GSM only, urban telephone line DISENABLED
6 During GSM functioning the outgoing Dial Tone is pulsed (Italy)
7 Activation of the Open Collector 3 output by vocal call in RTC or
command SMS of a number memorized as User on Sim Card
Phonebook
8 After the number of rings programmed, it always replies. It activates
the RING on simulated line also with unknown incoming calls.
9 Block of the exceeding SMS – DISENABLED
() GSM Anomaly: GSM off - GSM not replying in series - missing GSM service - missing GSM coverage
() R000 must always be programmed, even if empty with no phone number
() if a contract Sim Card is used, save figures 0 and/or 4 in order to disenable the management of the left-over credit
Note: the outputs programmed for functions - Output by incoming RING / Output for GSM anomaly/ Output for missing PSTN- cannot be activated
by incoming command SMS.
Set Italian language
Set English language
Set French language
Set Flemish language
- 27 -
It is automatically cancelled after it is entered
It is automatically cancelled after it is entered
Language configured
PRESENCE of parameter
Management of left-over credit on Main Sim Card (SIM A)
DISENABLED
Activation of the Open Collector 1 output also by incoming call
(RING) of one of the numbers memorized as User in the Sim
Card Phonebook
Activation of the Open Collector 2 output for GSM anomaly ()
Secondary Sim Card (SIM B) PRESENT
Management of left-over credit on secondary Sim Card (SIM B)
DISENABLED
Control on urban telephone line ENABLED, it switches to GSM
if missing
During GSM functioning the outgoing Dial Tone is continuous
(Abroad)
Activation of the Open Collector 3 output in absence of urban
telephone line (PSTN)
After the number of rings programmed, it replies only to memorized
users' phone numbers. It activates the RING on simulated line only
for memorized phone numbers
Block of exceeding SMS – ENABLED. The block only regards the
SMS produced inside the single call made by the control panel
having the conversion from Contact ID to SMS

) into the Sim Card