Monacor PA-803 DAP Bedienungsanleitung Seite 11

230 V~
50 Hz
FUSE
USE ONLY WITH A 250V FUSE
24 V
COM 4 Ω
ON
No. 1
for
CH 2 CH 3
input
Position Mikrophone
OFF level
Position
line level
ON
*Important: When phantom power has been acti-
vated, do not connect any microphone or audio unit
with unbalanced output signal to the input CH1; the
microphone/audio unit may be damaged .
Note: When announcements are being made via
the channels CH 2 and CH 3, the signals of the music
module and of the inputs CH 4 and CH 5 will be
slightly attenuated .
2) To connect audio sources with line level out-
put (e . g . CD player, mixer), use the following
jacks:
– RCA jacks CH 4 and CH 5
– 6 .3 mm jacks CH 2 and CH 3
Note: The inputs CH4 and CH5 are provided with
a pair of jacks for the connection of audio stereo
sources . The amplifier will create a mono signal from
the stereo signal . To connect stereo audio sources to
the inputs CH 2 and CH 3, use a stereo/mono adapter
(e . g . SMC-1) .
When connecting the audio sources to the
jacks CH 2 and CH 3, set the DIP switches 1
and 2 to the position ON (also see table) .
3) For important (emergency) announce-
ments, use the input TEL INPUT . It is possible
to connect, for example, a telephone system
with line level output to this input .
Note: A signal at the input TEL INPUT will mute all
other channels . When DIP switch 4 is in the position
OFF, however, announcements made via the input
MUTE ANTENNA
SPEAKER OUTPUT TEL INPUT
8 Ω 16 Ω 70 V 100 V COM
OFF
ON
1 2 3 4
SELECT
2 3 4
CH 1 and
CH 1
TEL INPUT
phantom
CH 1 has
power
highest priority
OFF
phantom
TEL INPUT has
power
highest priority
ON*
MOH OUTPUT
1 ON - CH 2 LINE 3 ON - PH. POWER CH 1 ON
600 Ω/100 mV 600 Ω/1 V OFF - CH 2 MIC OFF - PH. POWER CH 1 OFF
+ +
COM
2 ON - CH 3 LINE 4 ON - PRIO. TEL
OFF - CH 3 MIC OFF - PRIO. CH 1
CH 2 CH 3
CH 1 will have highest priority and will also mute the
channel TEL INPUT .
4) Connect a DAB / FM antenna to the jack
ANTENNA . With good reception conditions,
the wire antenna provided can be used .
5) If it is necessary to mute the speaker out-
puts, connect the two MUTE terminals, e . g .
via a switch .
3.2 Outputs
1) Speakers: Either connect 100 V or 70 V
speakers to the terminals "100V" or "70V"
and "COM" (page 2, fig . 1) . The load by
the speakers must not exceed the power rat-
ing of the amplifier (chapter 5); otherwise, the
protective circuit will interrupt the connection
to the speaker terminals .
Or connect a speaker or a speaker group to
the terminals "4 Ω", "8 Ω" or "16 Ω" and
"COM" . The total impedance of the speakers
must not fall below the value indicated at the
terminal used . Figure 2 on page 2 shows
various ways to observe the minimum imped-
ance . There are, however, also other possi-
bilities .
2) At the RCA jacks REC OUT 1 and 2, the mixed
signal is available . The control MASTER will not
have any effect on the volume of this signal .
The jacks can also be used, for example, for
a recorder or additional PA amplifiers if
more speakers are required than PA-803DAP
can handle .
3) The output MOH OUTPUT (music on hold) is
able to provide, for example, music on hold for
a telephone system . The mixed signal is also
available at this output . The control MASTER
will not have any effect on the volume .
2 1
3
1 2 3 4
OFF
1 2 3 4
ON
ON
SELECT CH 1
CH 4 CH 5 REC OUT
11