Landxcape LX992 Benutzerhandbuch Seite 14

4. Understanding Your Landxcape
Congratulations on your new purchase of Landxcape
to the care-free life of automatic mowing. In the following, we want to
help you to better understand how your Landxcape
4.1 How does my Landxcape
to mow?
TM
Landxcape chooses its direction at random. It will make sure your
entire lawn is evenly mowed without leaving unattractive mowing paths
(See Fig. A).
4.2 How does my Landxcape
where to go?
TM
Your Landxcape is made to work on its own. Landxcape
when it needs to go to its charging base to charge, can sense when it is
raining, can stop itself if it senses a problem, and knows to stop, draw
back, and turn around when it bumps into something blocking its path.
TM
Landxcape will also automatically stop its blade turning disc from
rotating if it is lifted off the ground to prevent an accident.
A. Finding the Charging Base
TM
When your Landxcape needs to recharge, it will stop mowing and
follow the boundary wire in an anti-clockwise direction back to its
TM
charging base. Landxcape is pre-programmed to mow the grass near
the boundary wire twice a week. By default, Landxcape
near the boundary wire every Monday and Friday after it is powered on.
If you don't want to enable boundary cut, deactivate it via your
smartphone (only for specific model, please check Technical Data &
Declaration of Conformity).
B. Rain sensors(only for specific model, please check Technical
Data & Declaration of Conformity)
TM
Landxcape is equipped with a rain sensor which detects rain and tells
TM
Landxcape to stop mowing and follow the boundary wire back to its
charging base (See Fig. B).
TM
Landxcape will resume mowing after passing the delay time. The
default delay time is 180mins. The delay time setting can be changed
TM
via Landxcape APP (only for specific model, please check Technical
Data & Declaration of Conformity).
When the rain sensors are wet, Landxcape
base. When the rain sensors are dry, Landxcape
delay time countdown. If you want to exit from the rain delay, dry the
sensor area, and perform a power cycle by operating the on/off key.
After the power cycle has been performed, you can operate again.
Or you can activate or deactivate the rain delay by using mobile App
(only for specific model, please check Technical Data & Declaration of
Conformity).
14
TM
TM
and welcome
TM
thinks.
TM
know what
TM
know
TM
knows
TM
will mow
TM
returns to its charging
TM
will begin the
C. Sensing the boundary wire
TM
Landxcape always obeys the border set by the boundary wire and
uses sensors at its front to detect it. (See Fig. C)
D. Starting and stopping while mowing (See Fig. D, E1, E2)
To start mowing, press the on/off key and input the PIN code. Press
, then press . If you would like Landxcape
press the STOP button on top of the mower.
TM
If Landxcape senses something is wrong, it will display a fault message
on the display. For information on these messages, refer to the Error
TM
Messages. Landxcape will turn off if it does not receive any input from
the user within 20 minutes.
To resume:
• Press , then press
TM
• Now Landxcape will begin to mow!
4.3 Setting
First please set the height to a desired grass level after cut (manually).
And you can do the program setting manually or using mobile App
(only for specific model, please check Technical Data & Declaration of
Conformity).
NOTE: When doing the program setting manually, Landxcape
enter the standby page if it does not receive any input from the user
within 30 seconds.
(1)Change PIN code
To change the PIN code, keep pressing both
same time for 5 seconds. The icon
" will be rolling flashing. After that, the first number will be blinking, use
or to input the old PIN code and press
will be blinking. Use the same method to complete other numbers. Then,"
" will be rolling flashing , the first number will be blinking and
use or to select the number you want and press
The next number will be blinking. Use the same method to complete other
numbers. For example, the new PIN code is set to be 0326. After that, "
" will be rolling flashing and the first number will be blinking again.
Use the same method to input the new PIN code you set just now (in this
example, ). Then "
display. Your PIN code has been changed successfully.
Only for reference
(2) Set year, date and time
Set year, date and time are compulsory setting items. If you don't set
these items, it will influence the schedule time in the following setting.
These items should be set in the order of year, date and time. For the year
setting, keep pressing for 3 seconds until the icon
are blinking on the display, for example,
select the year you want. Then press
setting.
TM
to stop mowing, simply
will
TM
and buttons at the
will be blinking, and "
to confirm. The next number
to confirm.
" will be rolling flashing on the
and a number
. Use or to
to confirm to finish the year
EN