Makita GA037G Betriebsanleitung Seite 16

Mount the wheel guard with the protrusions on the
wheel guard band aligned with the notches on the bear-
ing box. Then rotate the wheel guard to such an angle
that it can protect the operator according to work. Be
sure to tighten the screw securely.
To remove wheel guard, follow the installation proce-
dure in reverse.
► Fig.10: 1. Wheel guard 2. Bearing box 3. Screw
Installing or removing depressed
center wheel or flap disc
Optional accessory
WARNING:
When using a depressed center
wheel or flap disc, the wheel guard must be fitted
on the tool so that the closed side of the guard
always points toward the operator.
CAUTION:
Make sure that the mounting part
of the inner flange fits into the inner diameter of
the depressed center wheel / flap disc perfectly.
Mounting the inner flange on the wrong side may
result in the dangerous vibration.
Mount the inner flange onto the spindle.
Make sure to fit the dented part of the inner flange onto
the straight part at the bottom of the spindle.
Fit the wheel/disc on the inner flange and screw the lock
nut with its protrusion facing downward (facing towards
the wheel).
► Fig.11: 1. Lock nut 2. Depressed center wheel
3. Inner flange 4. Mounting part
To tighten the lock nut, press the shaft lock firmly so
that the spindle cannot revolve, then use the lock nut
wrench and securely tighten clockwise.
► Fig.12: 1. Lock nut wrench 2. Shaft lock
To remove the wheel, follow the installation procedure
in reverse.
Installing or removing flex wheel
Optional accessory
WARNING:
Always use supplied guard when
flex wheel is on the tool. Wheel can shatter during
use and guard helps to reduce chances of personal
injury.
► Fig.13: 1. Lock nut 2. Flex wheel 3. Back up pad
4. Inner flange
Follow instructions for depressed center wheel but also
use back up pad over wheel. See order of assembly on
accessories page in this manual.
Installing or removing abrasive disc
Optional accessory
► Fig.14: 1. Sanding lock nut 2. Abrasive disc
3. Rubber pad
1.
Mount the rubber pad onto the spindle.
2. Fit the disc on the rubber pad and screw the sand-
ing lock nut onto the spindle.
3. Hold the spindle with the shaft lock, and securely
tighten the sanding lock nut clockwise with the lock nut
wrench.
To remove the disc, follow the installation procedure in
reverse.
NOTE: Use sander accessories specified in this man-
ual. These must be purchased separately.
Installing or removing Ezynut
Optional accessory
Only for tools with M14 spindle thread.
CAUTION:
Do not use Ezynut with Super
Flange or angle grinder with "F" on the end of
the model No. Those flanges are so thick that the
entire thread cannot be retained by the spindle.
Mount inner flange, abrasive wheel and Ezynut onto the
spindle so that Makita Logo on Ezynut faces outside.
► Fig.15: 1. Ezynut 2. Abrasive wheel 3. Inner flange
4. Spindle
Press shaft lock firmly and tighten Ezynut by turning the
abrasive wheel clockwise as far as it turns.
► Fig.16: 1. Shaft lock
To loosen the Ezynut, turn the outside ring of Ezynut
counterclockwise.
NOTE: Ezynut can be loosened by hand as long
as the arrow points the notch. Otherwise a lock nut
wrench is required to loosen it. Insert one pin of the
wrench into a hole and turn Ezynut counterclockwise.
► Fig.17: 1. Arrow 2. Notch
► Fig.18
Installing abrasive cut-off / diamond
wheel
Optional accessory
WARNING:
/ diamond wheel, be sure to use only the special
wheel guard designed for use with cut-off wheels.
(In some European countries, when using a diamond
wheel, the ordinary guard can be used. Follow the
regulations in your country.)
WARNING:
grinding.
Mount the inner flange onto the spindle.
Fit the wheel / disc on the inner flange and screw the
lock nut onto the spindle.
► Fig.19: 1. Lock nut 2. Abrasive cut-off wheel / dia-
mond wheel 3. Inner flange 4. Wheel guard
for abrasive cut-off wheel / diamond wheel
For Australia and New Zealand
► Fig.20: 1. Lock nut 2. Outer flange 78 3. Abrasive
cut-off wheel / diamond wheel 4. Inner
flange 78 5. Wheel guard for abrasive cut-
off wheel / diamond wheel
16 ENGLISH
When using an abrasive cut-off
NEVER use cut-off wheel for side