Technical Data; Maintenance And Care - Scheppach PM1600 Originalbetriebsanleitung

Start-up
Turning on and off
Turning on (Fig.1)
Press and hold the circuit breaker (8) for the ON / OFF
switch; now you can press the ON / OFF switch (7) to
start the handheld mixer. Once the tool is running pro-
perly you can release the ON / OFF switch, turning off
the circuit breaker (8).
Turning off (Fig.1)
Release the ON / OFF switch (7). The circuit breaker
for the ON / OFF switch (8) turns off automatically.
Speed controller (Fig.1)
With the speed controller (9), the power tool's speed
can be gradually adjusted. The type of material to
be mixed determines the speed rate that is required.
Practice will teach you the optimal speed required by
the respective material.
2- speed gear (Fig.1)
The device is equipped with a 2-speed gear.
• For the speed selection turn the switch (4) by 180°.
1. speed: 0 min
2. speed: 0 min
Only operate this switch at standstill.
Working with the paint and mortar mixing tool
Before changing the mixing tool you must pull the po-
wer plug.
Reduce the working speed when you immerse the mi-
xing tool into the material you want to mix and when
you take it out again. When the mixing tool is fully im-
mersed, raise the speed to maximum in order to ensu-
re adequate cooling of the motor. Move the mixing tool
through the mixing container during the mixing operati-
on. Continue mixing until all the material has been tho-
roughly processed. When you are finished with your
mixing work, clean the mixing tool.

Technical data

Mains voltage
Power input
Idling speed
Mixing tool mount
Protection class
Weight
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 60745.
Sound pressure level L
Uncertainty K
Sound power level L
Uncertainty K
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.
Vibration emission value ah = 4.43 m/s
K uncertainty = 1.5 m/s
14 І 60
Heruntergeladen von manualslib.de
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
- 580 min
–1 –1
- 780 min
-1 -1
230 V~, 50 Hz
0-580 min / 0-780 min
-1
86 dB(A)
pA
pA
WA
WA
2
2
Handbücher-Suchmachiene
Additional information for electric power tools
Warning!
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in exceptio-
nal circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial as-
sessment of a harmful effect.
Keep the noise emissions and vibrations to a mi-
nimum.
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

Maintenance and Care

Before each maintenance and cleaning work:
• switch off device
• wait for standstill of the beater
• pull out power plug
Use only original parts. Other parts can result in unex-
pected damages and injuries.
Maintenance and repair work beyond this is only allo-
wed to be carried out by the manufacturer or autho-
rized service staff.
Store unused equipment in a dry, locked place out of
the reach of children.
Observe the following to maintain the operability of the
machine:
• Keep vent slits clean and free from obstructions.
1600 W
• Remove dust and dirt using a cloth or a soft brush.
-1
• Do not clean the machine with running water or
M14
highpressure cleaners.
• Do not use solvents for the synthetic parts (petrol,
II
alcohol, etc.) as these can damage the synthetic
5,2 kg
parts.
• Check that the handles are properly secured.
• Clean the beaters.
• The agitator is equipped with carbon brushes. Have
the carbon brushes be replaced by the customer
service if they are worn
Regularly check the beater for damages for your own
3 dB(A)
safety. Immediately replace any damaged beater. Al-
97 dB(A)
ways replace the beaters in pairs.
3 dB(A)
Check the shaft on a regular basis. An agitator with
defective shaft must no longer be used. Have the de-
vice be repaired by the customer service.