Maintenance - Milwaukee M12 CDD Originalbetriebsanleitung

TECHNICAL DATA CORDLESS PERCUSSION DRILL/
Production code........................................................................................
..............................................................................................................
Drilling capacity in steel ............................................................................
Drilling capacity in wood ...........................................................................
Drilling capacity in brick and tile ...............................................................
Wood screws (without pre-drilling) ...........................................................
No-load speed 1st gear ............................................................................
No-load speed 2nd gear ...........................................................................
Percussion rate 1st gear...........................................................................
Percussion rate 2nd gear .........................................................................
Torque max (Li-Ion Battery 1.5 Ah) *1 ......................................................
Torque max (Li-Ion Battery 3.0 Ah) *1 ......................................................
Battery voltage..........................................................................................
Drill chuck range .......................................................................................
Weight according EPTA-Procedure 01/2003 ...........................................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) .........................................
Sound power level (Uncertainty K=3dB(A)) ..............................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Vibration emission value a
h
Percussion drilling into concrete ...........................................................
Uncertainty K= ......................................................................................
Drilling into metal...................................................................................
Uncertainty K= ......................................................................................
Screwing ...............................................................................................
Uncertainty K= ......................................................................................
*1 Measured according to Milwaukee Standard N 877318
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may
be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent
accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not
actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden
wiring. Contact with a "live" wire will also make exposed metal parts of
the power tool "live" and shock the operator.
SCREWDRIVER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when performing
an operation where the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working
with the machine. The use of protective clothing is recommended, such
as dust mask, protective gloves, sturdy non-slip footwear, helmet and
ear defenders.
The dust produced when using this tool may be harmful to health. Do
not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
16 ENGLISH
M12 CDD M12 CPD
DRIVER
...........................4488 82 03... ................... 4488 85 03...
...........................4403 91 03... ................... 4403 71 03...
...000001-999999 ...000001-999999
................................ 13 mm ................................. 13 mm
................................ 25 mm ................................. 25 mm
................................... - ....................................... 13 mm
.................................. 8 mm ................................... 8 mm
........................... 0-450 min -1 ..........................0-450 min
......................... 0-1700 min -1 ........................0-1700 min
................................... - ................................0-6750 min
................................... - ..............................0-25500 min
................................ 37 Nm ................................. 37 Nm
................................ 44 Nm ................................. 44 Nm
................................ 12 V .................................... 12 V
.......................... 1,5-13 mm ...........................1,5-13 mm
............................. 1,34 kg ................................ 1,34 kg
................................ 91 dB (A) ............................. 91 dB (A)
.............................. 102 dB (A) ........................... 102 dB (A)
.................................... .................................... 30,8 m/s
.................................... .................................... 4,06 m/s
............................. 1,27 m/s ............................. 1,27 m/s
2
............................... 1,5 m/s ............................... 1,5 m/s
2
............................. 1,27 m/s ............................. 1,27 m/s
2
............................... 1,5 m/s ............................... 1,5 m/s
2
Switch the device off immediately if the insertion tool stalls! Do not
switch the device on again while the insertion tool is stalled, as doing
so could trigger a sudden recoil with a high reactive force. Determine
why the insertion tool stalled and rectify this, paying heed to the safety
instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric
cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces
can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors off er to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short circuit
risk).
Use only System M 12 chargers for charging System M 12 battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
-1
Warning! To reduce the risk of fi re, personal injury, and product
-1
damage due to a short circuit, never immerse your tool, battery pack or
-1
charger in fl uid or al-low a fl uid to fl ow inside them. Corrosive or
-1
conductive fl uids, such as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., Can cause a short circuit.
SPECIFIED CONDITIONS OF USE
M12 CDD: The battery drill/screwdriver may be used for drilling and
screwdriving for independent use away from mains supply.
M12 CPD: The electronic battery percussion drill/screwdriver may be
used for drilling, percussion drilling, as well as screwdriving for
independent use away from mains supply.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" fulfi lls all the relevant regulations and the
directives 2011/65/EU (RoHs), 2014/30/EU, 2006/42/EC, and the
2
following harmonized standards have been used:
2
EN 60745-1:2009 + A11:2010
2
EN 60745-2-1:2010
2
EN 60745-2-2:2010
2
EN 55014-1:2006 + A1:2009 + A2:2011
2
EN 55014-2:2015
EN 50581:2012
Winnenden, 2017-11-30
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk of
overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack from
the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away
from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations
that cause high current draw, the tool will vibrate for about 5 seconds,
the fuel gauge will fl ash,and then the tool will turn OFF. To reset,
release the trigger.
Under extreme circumstances, the internal temperature of the battery
pack could raise too much. If this happens, the fuel gauge will fl ash
until the battery pack cooled down. After the lights go off , the work may
continue.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice

MAINTENANCE

Use only Milwaukee accessories and spare parts. Should components
need to be replaced which have not been described, please contact
one of our Milwaukee service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be ordered. Please state
the machine type printed as well as the six-digit No. on the label and
order the drawing at your local service agents or directly at: Techtronic
Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before
carrying out any work on the machine.
Please read the instructions carefully before starting
the machine.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
National mark of conformity Ukraine
EurAsian Conformity Mark.
ENGLISH 17