Maintenance - Milwaukee HDE 13 RQD Betriebsanleitung

Clamp your workpiece with a clamping device. Unclamped workpieces
can cause severe injury and damage.
Switch the device o immediately if the insertion tool stalls! Do not
switch the device on again while the insertion tool is stalled, as doing
so could trigger a sudden recoil with a high reactive force. Determine
why the insertion tool stalled and rectify this, paying heed to the
safety instructions.
Possible causes can be:
• it is tilted in the workpiece to be machined
• breakage of the material to be used
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burnswhen changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
SPECIFIED CONDITIONS OF USE
The drill can be used for drilling in wood, metal and plastics.
MAINS CONNECTION
Appliances used at many di erent locations including wet room and
open air must be connected via a residual current device (FI, RCD,
PRCD) of 30mA or less.
Connect only to single-phase AC system voltage as indicated on the ra-
ting plate. It is also possible to connect to sockets without an earthing
contact as the design conforms to safety class II.
Only plug-in when machine is switched o .
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" ful lls all the relevant provisions of the directives
2011/65/EU (RoHS)
2006/42/EC
2014/30/EU
and the following harmonized standards have been used.
EN 62841-1:2015
EN 62841-2-1:2018
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN IEC 63000:2018
Winnenden, 2020-11-23
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under „Technical Data" ful lls all the
relevant provisions of the following Regulations
S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended),
S.I. 2016/1091 (as amended) and that the following designated
standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-1:2018 + A11:2019
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 61000-3-2:2014
BS EN 61000-3-3:2013
BS EN IEC 63000:2018
Winnenden, 2020-11-23
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.
If the replacement of the supply cord is necessary, this has to be done
by the manufacturer or his agent in order to avoid a safety hazard.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described, please
contact one of our Milwaukee service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before carrying
out any work on the machine.
Please read the instructions carefully before starting the
machine.
Accessory - Not included in standard equipment, availa-
ble as an accessory.
Do not dispose of electric tools together with household
waste material. Electric tools and electronic equipment
that have reached the end of their life must be collected
separately and returned to an environmentally compatible
recycling facility. Check with your local authority or retailer
for recycling advice and collection point.
Class II tool. Tool in which protection against electric shock
does not rely on basic insulation only, but in which additional
safety precautions, such as double insulation or reinforced
insulation, are provided. There being no provision for protec-
tive earthing or reliance upon installation conditions.
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
n
No-load speed
0
V
Volts
AC Current
GB
English
11