Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
NETWORK SETUP
-------------------------------------------------------------------------------------------
Technical requirements
Most of the home networks are Dynamic. If
you have a dynamic network, you must use a
DSL modem that supports DHCP. Modems and
IP sharers that support DHCP obtain the »IP
Address«, »Netmask«, »Gateway« and »DNS«
values required for internet access automatical-
ly, and thus you are not required to enter those
values manually.
Wireless WPS network connection
through by pressing a button
1
Open the menu with »MENU«.
2
Select menu item »Settings« with »
V
«, »
Λ
«,
<
>
»
« or »
« and press »OK« to confirm.
>
3
Select the menu item »Network« with »
« or
<
»
« and press »
« to confirm.
V
– »Network« menu is active.
4
Select the line »Change Connection Type«
with »
V
« or »
Λ
« and press »OK« to
confirm.
5
Select the option »Wireless WPS« with »
V
«
or »
« and press »OK« to confirm.
Λ
– WiFi warning message will be displayed.
6
Confirm the message »Do you want to turn
<
>
on Wi-Fi?« select »Yes« with »
« or »
« and
press »OK« to confirm.
7
Select the line »WPS Type« with »
V
« or
»
« and select the option »Push Button«
Λ
<
>
with »
« or »
«.
Settings > Network
Tuesday
xx xxx xxxx
Picture
Sound
Source
TV
Network
Timer
Parental
Çhange Connection Type
Wireless WPS
WiFi
On
WPS Type
Push Button
Select Access Point
N/A
Network Configuration
Auto
Wake-on-LAN
Off
Connect
Test Connection
Change Area
Input Mode
BACK
Back
EXIT
Exit
8
With » « (red) select »Connect« to establish
modem connection.
– »Push the WPS button on your Access
Point« message is displayed.
9
Press the WPS button on the router.
92
ENGLISH
10
To continue after pressing the WPS button
on the access point, select the option »Con-
<
>
tinue« with »
« or »
«and press »OK« to
confirm.
– The "Connection to Gateway: Success"
message will be displayed.
11
Press » « (green) to make sure that the
network connection is established with the
current settings.
– »Testing ... Please wait« message will
be displayed, and if the connection is
established »Connection To Gateway:
Success«, »Internet Connection: Success«
messages will be displayed.
12
Press »EXIT« to end the setting.
Wireless WPS network connection with
PIN
1
Open the menu with »MENU«.
2
Select menu item »Settings« with »
«, »
«,
V
Λ
<
>
»
« or »
« and press »OK« to confirm.
>
3
Select the menu item »Network« with »
« or
<
»
« and press »
V
« to confirm.
– »Network« menu is active.
4
Select the line »Change Connection Type«
with »
« or »
« and press »OK« to
V
Λ
confirm.
<
5
Select the option »Wireless WPS« with »
«
>
or »
« and press »OK« to confirm.
– WiFi warning screen will be displayed.
6
Confirm the message »Do you want to turn
<
>
on Wi-Fi?« select »Yes« with »
« or »
« and
press »OK« to confirm.
7
Select the line »WPS Type« with »
V
« or
<
»
« and select the option »PIN« with »
«
Λ
>
or »
«.
Settings > Network
Tuesday
xx xxx xxxx
Picture
Sound
Source
TV
Network
Timer
Parental
Çhange Connection Type
Wireless WPS
WiFi
On
WPS Type
PIN
Select Access Point
N/A
Network Configuration
Auto
Wake-on-LAN
Off
BACK
Back
EXIT
Exit
Change Area
Change Mode
NETWORK SETUP
-------------------------------------------------------------------------------------------
8
Select the line »Select Access Point« with
»
V
« or »
Λ
« and press »OK« to confirm.
– Present WPS-supported wireless networks
are scanned to display in the »Select Ac-
cess Point« menu.
9
Select the network that you want to connect
with »
« or, »
« and press »OK« to
V
Λ
confirm.
– 8-digit pin code is displayed in the wire-
less WPS menu.
Note:
Refer to the manual of your router to find
7
out how the PIN is entered via a PC.
10
Use a PC to enter the pin on the router (e.g.
AVM FRITZ!Box: menu item WLAN Set-
tings... WPS) and save.
Note:
The 8-digit PIN code must be entered in the
7
modem interface in 2 minutes; otherwise,
connection of television with the modem is
cut.
11
Press » « (green) to confirm the registra-
tion.
– The message "Connection to Gateway:
Success" appears.
12
Press » « (green) to check the performed
settings and also if the local network and
internet connection has been established.
– »Testing ... Please wait« message will
be displayed, and if the connection is
established »Connection To Gateway:
Successfull«, »Internet Connection: Suc-
cessfull« messages and MAC address will
be displayed.
13
Press »EXIT« to end the setting.
Connecting automatically by entering
the network password
Use this method for establishing a connection
if your router does not support "WPS-PBC" or
WPS PIN entry.
1
Open the menu with »MENU«.
2
Select menu item »Settings« with »
V
«, »
Λ
«,
<
>
»
« or »
« and press »OK« to confirm.
>
3
Select the menu item »Network« with »
« or
<
»
« and press »
« to confirm.
V
– »Network« menu is active.
Settings > Network
Tuesday
xx xxx xxxx
Picture
Sound
Source
TV
Network
Timer
Parental
Change Connection Type
Wired
Network Configuration
AUTO
Wake-on-LAN
Off
Advanced
Connec
Test Connection
Change Area
Select
Back
BACK
4
Select the line »Change Connection Type«
with »
« or »
« and press »OK« to
V
Λ
confirm.
5
Select the option »Wireless« with »
« or
V
»
Λ
« and press »OK« to confirm.
– WiFi warning message will be displayed.
6
Confirm the message »Do you want to turn
<
>
on Wi-Fi?« select »Yes« with »
« or »
« and
press »OK« to confirm.
7
Select the line »Network Configuration«
with »
V
« or »
Λ
« and select the option
<
>
»AUTO« with »
« or »
«.
8
Select the line »Select Access Point« with
»
« or »
« and press »OK« to confirm.
V
Λ
– »Select Access Point« menu is displayed
by scanning available wireless networks.
9
Select the network that you want to con-
nect with »
« or »
« and press »OK« to
V
Λ
confirm.
– Wireless connection password screen is
displayed.
ENGLISH
93
Werbung
Inhaltsverzeichnis
