Displaying Signal Information - Grundig Chassis G5 Serviceanleitung

NETWORK SETUP
-------------------------------------------------------------------------------------------
Connecting the TV to a "hidden"
network
Even if the SSID (Service Set Identifier) of the
router is not visible, you can connect your TV to
this network.
1 Open the menu with »MENU«.
2 Select menu item »Settings« with » «, » «,
V Λ
< >
» « or » « and press »OK« to confrim.
>
3 Select the menu item »Network« with » « or
<
» « and press » V « to confirm.
– »Network« menu is active.
4 Select the line »Select Access Point« with
» « or » « and press »OK« to confirm.
V Λ
– »Select Access Point« menu appears and
available wireless networks are scanned
and displayed in the menu.
5 Press » « (red).
– »Add Network« menu appears.
6 Select the line »Access Point Name« with
» V « or » Λ « and press »OK« to confirm.
– A menu for entering the SSID will be
displayed.
Note:
For device to discover the wireless modem
7
on the network, the network name should
support ASCII characters.
7
Select the required character with » V «,
< >
» Λ «, » « or » « and move to the next
character with »OK«.
– Using »Shift« »OK«, you can switch
between uppercase letters / numbers and
lowercase letters / special characters.
– Select »Del« to delete the character
entered and press »OK« to confirm.
8 Confirm the SSID by pressing » « (green).
9
Select the line »Security Type« with » V « or
» « and select the required option (WPA2)
Λ
< >
with » « or » «.
10 Confirm the setting with » « (red).
– The network is now in the »Select Access
Point« menu.
94 ENGLISH
11
Select the network with » V « or » Λ « and
press »OK« to confirm.
– Wireless connection password screen is
displayed.
12
Select the required character with » V «,
< >
» Λ «, » « or » « and move to the next
character with »OK«.
– Using »Shift« »OK«, you can switch
between uppercase letters / numbers and
lowercase letters / special characters.
– Select »Del« to delete the character
entered and press »OK« to confirm.
13 Confirm the password by pressing » «
(green).
– »Connecting ... Please wait« message will
be displayed.
14 Press » « (green) to make sure that the
network connection is established with the
current settings.
– »Testing ... Please wait« message will
be displayed, and if the connection is
established »Connection To Gateway:
Success«, »Internet Connection: Success«
messages and MAC address will be
displayed.
15
Press »EXIT« to end the setting.
SETTING FURTHER CHANNELS
Creating a list of favourites - analog
channels
You can select your favourite channels and save
them in up to four lists (FAV1 to FAV4).
1 In the »Channel Editor« menu, select the
channel(s) you want to add in the favor-
< >
ites list with » V «, » Λ «, » « or » «, and
highlight the television channel by pressing
»OK«.
–Channel is marked with » «.
2 Activade the »Tools« menu with » « (yel-
low).
3
Select the line »Add To Fav.« with » V « or
» « and press »OK« to confirm.
Λ
–»Add to Fav.« menu is displayed.
4 Select the favorite list you want to add the
selected channels with » V « or » Λ « and
store with »OK«.
– The channels are marked in the Channel
Editor with » «, » «, » « or » «.
– You can add the same channel in more
than one favourites list.
– Each favourite list can contain maximum
255 channels.
Notes:
You can delete channels from the favou-
7
rites list. Press » « (yellow), select the
favorites list the channel is in with » V « or
» Λ « and press »OK« to confirm. Select the
channel(s) you want to delete with » «,
V
< >
» Λ «, » « or » «, and highlight the channel
by pressing »OK«.
Press » « (yellow) and select the line
»Remove from Fav.« with » V « or » Λ « and
confirm with »OK«. The channel you have
selected is now deleted from the favorites
list.
When a channel stored in the favourite
7
channel list is deleted channel order in the
favourite list is updated.
5 Press »EXIT« to close the menu.
108 ENGLISH
-----------------------------------------------------

Displaying signal information

(only for digital television channels)
1 Open the menu with »MENU«.
2 Select menu item »Settings« with » «, » «,
V Λ
< >
» « or » « and press »OK« to confirm.
>
3 Select the menu item »Source« with » « or
<
» « and press » V « to confirm.
– »Source« menu is active.
4
Select the line »Advanced« with » V « or
» « and press »OK« to confirm.
Λ
5 Select the line »Signal Information« with
» « or » « and press »OK« to confirm.
V Λ
– »Signal Information« menu is displayed.
Notes:
Signal information changes depending on
7
the current source.
Signal information is shown at the top of the
7
menu. The more »Frequency« and »Signal
Strength« bar stretches to the right, the more
signal you have.
The signal level not only depends on your
7
receiver system, but also on the channel
which is currently active. Remember this
when aligning your antenna using the
signal level display.
6
Press »EXIT« to close the menu.