Changing The Pressure Unit; Bar); Inflating Tyres - Formula 1 HI700 Originalbetriebsanleitung

EN
2. Select the desired valve adapter from the stor-
age compartment (12).
3. Open the lock-on lever (13) by pushing the
lock-on lever away from the air hose (14).
4. Now attach the valve adapters and push the
lever toward the air hose to lock it in place.
Changing the pressure unit (PSI, kPA
or bar)
Press the „PSI/BAR/KPA" button (3) until the
display (5) shows the desired pressure unit. The
default value flashes.

Inflating tyres

•
The tyre pressure increases as the tempera-
ture rises. The recommended tyre pressure is
typically specified for cold tyres (approx. 20 °C).
Please refer to the owner's manual for your
vehicle.
•
Do not check the tyre pressure on warm tyres
(e.g. after long trips).
Attention!
The compressor may be operated for max. 10
minutes, after which the device must cool down
for 10 minutes!
1. No valve adapter required to inflate car tyres.
First remove the cap from the tyre valve.
2. Release the lock-on lever and place the lock-
on lever (13) as far on the tyre valve as pos-
sible. Close the lock-on lever in the process.
3. Verify the automotive valve lever plug is firmly
attached to the tyre valve by carefully pulling
on it.
4. Press the „+" (2) or „-" button (4) until the set
value in the display (5) corresponds with the
desired pressure.
5. Set the toggle switch (6) to „I" to switch on the
compressor.
Note: The compressor can be switch off at any
time by setting the toggle switch (6) to the „O"
position.
The compressor increases the tyre pressure ac-
cording to the set value and stops automatically.
6. Set the toggle switch (6) to „0" to switch off
the compressor.
7. Release the lock-on lever and remove the
lock-on lever (13) from the tyre valve.
16 f1.mts-gruppe.com
8. Also check the air pressure with a second
pressure gauge to determine the accurate
value. Repeat the process if the desired air
pressure has not been reached.
9. Then replace the valve cap on the tyre valve.
Inflating sporting goods, toys and
recreational products
Attention!
The compressor may be operated for max. 10
minutes, after which the device must cool down
for 10 minutes!
1. First read the product manufacturer's instruc-
tions for inflating and the approved maximum
air pressure before inflating the product.
2. Open the product's valve cover.
3. Connect the air hose (17) to the air outlet (9).
4. Insert the other end of the air hose (17) in the
item's valve. If the air hose comes out of the
valve whilst inflating, you will need to push it
into the valve with your hand whilst inflating.
5. Slightly tug on the air hose to verify it is seated
tight in the item's valve.
6. Set the toggle switch (6) to „II" to switch on
the compressor.
Note: The compressor can be switch off at any
time by setting the toggle switch (6) to the „O"
position.
Attention!
Observe and check the firmness of the item
whilst inflating. If the item has already been over-
inflated, immediately interrupt the process and
switch the compressor off! Attention! Excessive
air pressure may cause the item to burst! Risk of
personal injury and property damage!
7. Set the toggle switch (6) to „0" to switch off
the compressor.
8. Remove the air hose from the item's valve and
close the valve cover on the item.
Deflate function
The deflate function can be used to reduce the air
pressure in an inflated item.
1. Connect the air hose (17) to the air inlet (15).
2. Insert the other end of the air hose (17) in the
item's valve.
3. Set the toggle switch (6) to „II" to switch on
the compressor.
The compressor reduces the pressure in the item.