Bosch GWS Professional 18 V-LI Originalbetriebsanleitung Seite 19

OBJ_BUCH-1102-006.book Page 20 Thursday, June 5, 2014 1:02 PM
20 | English
Technical Data
Angle Grinder
Article number
Rated voltage
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Weight according to EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
**
– during operation and during storage
Recommended batteries
Recommended chargers
* dependent of the battery pack being used
** Limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 82 dB(A); Sound power level 93 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Surface grinding: a =6.0 m/s , K=1.5 m/s
h
2
Disk sanding: a =2.5 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-3.
1 609 92A 0N2 | (5.6.14)
min
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
2
,
Robert Bosch GmbH, Power Tools Division
2
.
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 12.05.2014
Assembly
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
GWS 18 V-LI
3 601 J3A 300
V= 18
-1
10000
mm 115
M 14
mm 22
kg 2.1/2.3*
°C 0...+45
°C –20...+50
GBA 18V ...
AL 18..
GAL3680
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
GWS 18-125 V-LI
3 601 J3A 301
18
10000
125
M 14
22
2.1/2.3*
0...+45
–20...+50
GBA 18V ...
AL 18..
GAL3680
Bosch Power Tools