Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
A
DESCRIPTION
(starts at page 35
1 Upper handles
2 Reduction gear
3 Fastening knobs for upper handles
4 Grass catcher
B
ASSEMBLY OF GRASS CATCHER (
C
ASSEMBLY REAR DEFLECTOR (
MULCHING CAP INSERTION (
D
To cut the grass with the mulching system (no grass collection), lift the rear deflector panel and insert the cap by fixing it with the spring as shown in the figure.
E
ASSEMBLY (
starts at page 36
F
ASSEMBLY (
starts at page 37)
G
ADJUSTMENT OF HANDLES HEIGHT (
H
ADJUSTMENT OF CUTTING HEIGHT (
SAFETY PRECAUTIONS (
I
l Always operate with the rear deflector or grass catcher in the correct position.
l Always stop the mower before removing the grass catcher or adjusting the height of cut.
l Never place your hands or feet underneath the deck or into the rear grass discharge chute while the mower is running.
(starts at page 38)
J
Before mowing, remove all foreign objects from the lawn which may be thrown by the machine. While mowing, stay alert for any foreign objects which may have been
missed.
Never lift the rear of the mower while starting or during normal operation.
(starts at page 38)
H
Never place your hands or feet underneath the deck or into the rear discharge chute while the mower is running.
OPERATION (
starts at page 38)
L
CONNECTION V220/230 - 50 Hz
ATTENTION MOTOR PROTECTOR
A motor cut -out device (motor protector) has been incorporated in the switch. Therefore, when reaching excessive cutting stress or overload, the motor will be cut out
automatically.
For re-starting, wait until the motor will be cool (approx. 5 to 10 minutes);
(starts at page 38)
M
OPERATION
Before connecting up the lawn mower to the electric power supply, make sure that the mains supply voltage is 220-230V/50Hz and that a ground fault interrupter is
installed on the mains circuit. Start the mower as follows:
a) Press the safety push-button (5) to enable mower startup.
b)Start the mower by pulling the lever (11) towards the handle and keeping it pressed down. If you release the lever, the motor will stop.
CAUTION! The blade starts turning as soon as the mower is started.
N
(starts at page 39)
MOWING
To cut the grass, push the lawn mower manually
(starts at page 39)
O
MOWING
To cut the grass, push the lawn mower manually or insert the automatic advance gear.
How to insert automatic advance: Lift up the clutch lever (13) and keep it pressed in position.
How to disengage advance: Release the clutch lever.
Important: If, when you press the clutch lever, the automatic advance gear does not engage, the clutch cable should be adjusted by inserting the spring (P)
in one of the subsequent holes (S) in the clutch lever (13).
AUTOMATIC ADVANCEMENT
P
Periodically check the automatic advance assembly and make sure to keep it clean. In particular, the pinion (14) and the gear (15) must be kept perfectly clean. To carry
out this check, you must remove the wheel (16) by unscrewing the screw (17). Before reinstalling the wheel, put grease on the pinion and gear.
All manuals and user guides at all-guides.com
)
5
Safety button
6
Switch
7
Deck
8
Cable holder
)
starts at page 35
If applicable
)
starts at page 35
If applicable
starts at page 35)
)
starts at page 38
starts at page 38
)
starts at page 38
(starts at page 39)
9
Rear deflector wall
10 Motor cover
11 Switch lever
Manual lawn mower
Assemble the handle and switchbox as shown.
Self-Propelled
Assemble the handle and clutch lever with pins and clips provided and assemble switchbox
as shown.
)
)
7
ENGLAND
12 Levers for adjusting the cutting height
13 Clutch lever
Werbung
Inhaltsverzeichnis
