Werbung
Verfügbare Sprachen
Verfügbare Sprachen
M M a a i i n n t t e e n n a a n n c c e e , , i i n n s s p p e e c c t t i i o o n n s s , , c c h h e e c c k k s s a a n n d d c c l l e e a a n n i i n n g g
Machine structure
• tightening of main bolts (screws, fixing systems, etc.) of
machine.
• Safety signs
check the readability and condition of safety signs.
• Electrical control panel
check the electrical components installed inside the electrical
control panel. Check the wiring between the electrical panel
and machine parts.
• Electrical connection cable and plug
check the connection cable (replace if necessary) and plug.
• Extraordinary machine maintenance
check all gas components (if present).
General machine overhaul
• check all components, electrical equipment, corrosion, pipes...
1.
the machine is designed and built for a duration of about 10 years. After this period of time (from commissioning) the machine must undergo a general
inspection and overhaul. Some examples of checks to be carried out are given below.
• Check for any oxidised electrical components or parts; if necessary, replace them and restore the initial conditions;
• Check the structure and welded joints in particular;
• Check and replace bolts and/or screws, also checking for any loose components;
• Check the electrical and electronic system;
• Check the functionality of safety devices;
• Check the general condition of protection devices and guards.
NOTE!
It is advisable to stipulate a preventive and scheduled maintenance contract with the Customer Care Service.
Disassembly
• All scrapping operations must occur with the machine stopped and cold and the electrical power supply disconnected.
• Work on the electrical equipment must only be carried out by a qualified electrician, with the power supply disconnected.
• To carry out these operations it is necessary to use: overalls, safety shoes and gloves.
• During disassembly and handling of the various parts, the minimum height from the floor must be maintained.
G G . . 1 1 . . 1 1 1 1 E E x x t t r r a a o o r r d d i i n n a a r r y y m m a a i i n n t t e e n n a a n n c c e e
NOTE!
Extraordinary maintenance must be carried out by
specialised personnel, who can ask the manufac-
turer to supply a servicing manual.
G G . . 1 1 . . 1 1 2 2 M M a a i i n n t t e e n n a a n n c c e e c c o o n n t t a a c c t t s s ( ( o o n n l l y y f f o o r r A A u u s s t t r r a a l l i i a a ) )
F F o o r r s s e e r r v v i i c c e e a a n n d d s s p p a a r r e e p p a a r r t t s s , , p p l l e e a a s s e e c c o o n n t t a a c c t t : :
H H
M M A A C C H H I I N N E E D D I I S S P P O O S S A A L L
W W A A R R N N I I N N G G
Refer to " WARNING AND Safety
Information "
H H . . 1 1
W W a a s s t t e e s s t t o o r r a a g g e e
At the end of the product's life-cycle, make sure it is not
dispersed in the environment. The doors must be removed
before scrapping the appliance.
SPECIAL waste materials can be stored temporarily while
awaiting treatment for disposal and/or permanent storage. In
any case, the current environmental protection laws in the
user's country must be observed.
H H . . 2 2
P P r r o o c c e e d d u u r r e e r r e e g g a a r r d d i i n n g g a a p p p p l l i i a a n n c c e e d d i i s s m m a a n n t t l l i i n n g g
m m a a c c r r o o o o p p e e r r a a t t i i o o n n s s
Before disposing of the machine, make sure to carefully check
its physical condition, and in particular any parts of the
structure that can give or break during scrapping.
F F r r e e q q u u e e n n c c y y
Yearly
Yearly
Yearly
Yearly
Yearly
1
Every 10 years
• Electrolux - Tom Stoddart Pty Ltd — 39 Forest Way,
Karawatha QLD 4117 — call 1-300-307-289
• Zanussi - Procook Australia Pty Ltd — 23 Rothesay Street-
Kenmore, Queensland 4069 — call 07-3868-4964
• Diamond - Semak Food Service Equipment — 18, 87– 91
Hallam South Road, Hallam VIC 3803 — call 03 9796 4583
The machine's parts must be disposed of in a differentiated
way, according to their different characteristics (e. g. metals,
oils, greases, plastic, rubber, etc.).
Different regulations are in force in the various countries,
therefore comply with the provisions of the laws and compe-
tent bodies in the country where scrapping takes place.
In general, the appliance must be taken to a specialised
collection/ scrapping centre.
Dismantle the appliance, grouping the components according
to their chemical characteristics, remembering that the com-
pressor contains lubricant oil and refrigerant fluid which can be
recycled, and that the refrigerator components are special
waste assimilable with urban waste.
28
R R e e s s p p o o n n s s i i b b i i l l i i t t y y
Service
Service
Service
Service
Service
Service
Werbung
