Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Polyethylene
• Outer wrapping
• Instructions bag
Polypropylene
• Straps
Polystyrene foam
• Corner protectors
E E . . 4 4
J J o o i i n n i i n n g g A A p p p p l l i i a a n n c c e e s s
1. Undo the 4 fixing screws and remove the control panels of
the appliances (Fig.1A);
2. Remove the fixing screw nearest the control panel, from
each side to be joined (Fig.1B);
3. Bring the appliances together and turn the feet to level
them until the tops match (Fig.1D);
4. Turn one of the two plates inside the appliances 180℃
(Fig.1C);
5. From inside the control panel of the same appliance, join
them at the front side, screwing one M5x40 Hex Head
screw (supplied) on the opposite insert (Fig.1E);
6. From the rear of the appliances, insert the coupling plate
(provided) in the side slots on the back panels;
7. Secure the plate with two flat head M5 screws provided
(Fig.1F).
1F
E E . . 4 4 . . 1 1
F F l l o o o o r r F F i i x x i i n n g g ( ( d d e e p p e e n n d d i i n n g g o o n n t t h h e e a a p p p p l l i i a a n n c c e e a a n n d d / / o o r r
m m o o d d e e l l ) )
To avoid accidental tipping of built-in half-module appliances
installed separately, fix them to the floor carefully following the
instructions enclosed with the corresponding accessory
(F206136).
1B
1C
1A
1E
1D
E E . . 4 4 . . 2 2
I I n n s s t t a a l l l l a a t t i i o o n n O O n n B B r r i i d d g g e e , , C C a a n n t t i i l l e e v v e e r r F F r r a a m m e e O O r r
C C e e m m e e n n t t P P l l i i n n t t h h ( ( d d e e p p e e n n d d i i n n g g o o n n t t h h e e a a p p p p l l i i a a n n c c e e a a n n d d / /
o o r r m m o o d d e e l l ) )
Carefully follow the instructions enclosed with the correspond-
ing accessory. Follow the instructions supplied with the
optional product chosen.
E E . . 4 4 . . 3 3
S S e e a a l l i i n n g g G G a a p p s s B B e e t t w w e e e e n n A A p p p p l l i i a a n n c c e e s s
Follow the instructions supplied with the optional sealing paste
pack.
E E . . 5 5
G G a a s s , , e e l l e e c c t t r r i i c c i i t t y y a a n n d d w w a a t t e e r r c c o o n n n n e e c c t t i i o o n n s s ( ( i i f f
p p r r e e s s e e n n t t , , d d e e p p e e n n d d i i n n g g o o n n t t h h e e a a p p p p l l i i a a n n c c e e a a n n d d / / o o r r
m m o o d d e e l l ) )
• Any installation work or maintenance to the supply system
(gas, electricity and/or water, if present) must only be
carried out by the utility company or an authorised
installation technician.
• Refer to the appliance dataplate for the product code.
• See the installation diagram for the type and position of
appliance connections.
E E . . 6 6
G G a a s s C C o o n n n n e e c c t t i i o o n n s s
E E . . 6 6 . . 1 1
I I n n t t r r o o d d u u c c t t i i o o n n
C C A A U U T T I I O O N N
This appliance is arranged and tested to
operate with G20 gas 20 mbar;
To convert it to another type of gas, follow the instructions in
E.6.6 Conversion to another type of gas paragraph of this
section.
E E . . 6 6 . . 2 2
F F u u m m e e e e x x h h a a u u s s t t
• "A1" type appliances have to be positioned under an
extraction hood to ensure removal of fumes and steam
produced by cooking;
(not relevant for Australian standard).
For A A U U S S T T R R A A L L I I A A : the ventilation must be in accordance with
Australian building codes and kitchen exhaust hoods must
comply with AS/NZS1668.1 and AS 1668.2.
E E . . 6 6 . . 3 3
B B e e f f o o r r e e c c o o n n n n e e c c t t i i n n g g
1. Make sure the appliance is arranged for the type of gas to
be used.
Otherwise, carefully follow the instructions given in E.6.6
Conversion to another type of gas paragraph of this section.
2. Fit a rapid gas shutoff tap/valve ahead of each appliance.
3. Install the tap/valve in an easily accessed place.
4. Clean the pipes to remove any dust, dirt or foreign matter
which could block the supply.
The gas supply line must ensure the gas flow necessary for
full operation of all the appliances connected to the system.
A supply line with insufficient flow will affect correct
operation of the appliances connected to it.
18
Werbung
