Drilling Operation; Optional Accessories - Makita DP2010 Betriebsanleitung

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and unplugged before carrying out
any work on the tool.
Installing or removing drill bit
For model DP2010
► Fig.4: 1. Drill chuck 2. Chuck key
To install the drill bit, place it in the drill chuck as far as
it will go. Tighten the chuck by hand. Place the chuck
key in each of the three holes and tighten clockwise. Be
sure to tighten all three chuck holes evenly.
To remove the drill bit, turn the drill chuck key counter-
clockwise in just one hole, then loosen the chuck by hand.
After using the chuck key, be sure to return it to the
original position.
For model DP2011
► Fig.5: 1. Sleeve 2. Ring
Hold the ring and turn the sleeve counterclockwise to
open the drill chuck jaws. Place the drill bit in the drill
chuck as far as it will go. Hold the ring firmly and turn
the sleeve clockwise to tighten the drill chuck.
To remove the drill bit, hold the ring and turn the sleeve
counterclockwise.
Depth gauge (optional accessories)
► Fig.6: 1. Depth gauge 2. Washer 3. Clamp screw
Install the depth gauge on the tool with the clamp screw
and washer. Adjust the depth gauge to the desired
depth and tighten the clamp screw.
OPERATION
Holding the tool
► Fig.7
Always hold the tool only by the handle when perform-
ing an operation. Do not touch the metal part.

Drilling operation

Drilling in wood
When drilling in wood, the best results are obtained
with wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the drill bit into
the workpiece.
Drilling in metal
To prevent the drill bit from slipping when starting a
hole, make an indentation with a center-punch and
hammer at the point to be drilled. Place the point of the
drill bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The excep-
tions are iron and brass which should be drilled dry.
CAUTION:
Pressing excessively on the tool
will not speed up the drilling. In fact, this excessive
pressure will only serve to damage the tip of your drill
bit, decrease the tool performance and shorten the
service life of the tool.
CAUTION:
Hold the tool firmly and exert care
when the drill bit begins to break through the
workpiece. There is a tremendous force exerted on
the tool/drill bit at the time of hole break through.
CAUTION:
A stuck drill bit can be removed
simply by setting the reversing switch to reverse
rotation in order to back out. However, the tool
may back out abruptly if you do not hold it firmly.
CAUTION:
Always secure workpieces in a
vise or similar hold-down device.
CAUTION:
Avoid drilling in material that you
suspect contains hidden nails or other things that
may cause the drill bit to bind or break.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and unplugged before attempting to
perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Drill bits
• Chuck key
• Chuck key holder
• Depth gauge
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
5 ENGLISH