Buttons And Indicator Lights - Shark IQ ROBOT SELF-EMPTY RV1000SEU Gebrauchsanweisung

BUTTONS AND INDICATOR LIGHTS

!
CLEAN BUTTON
Press to begin a cleaning
session. Press again to stop.
RECHARGE & RESUME
Press and hold the CLEAN
button for 15 seconds to
turn Recharge & Resume
ON or OFF.
The Recharge & Resume function is turned OFF by
default. Turn ON Recharge & Resume for complete
coverage if your home's floor plan is bigger than
1500 sq. ft. Your robot will return to the base,
recharge, and can pick up cleaning where it left off.
NOTE: If your floor plan is smaller than 1000 sq. ft., we recommend that you DO NOT use the Evacuate & Resume function.
s h a r kc l e a n . e u
BATTERY INDICATOR LIGHT
Displays the amount of
charge remaining in the
battery.
"!" ERROR INDICATOR
See Troubleshooting section
for full list of error codes.
WI-FI INDICATOR
Blue light: connected to
Wi-Fi.
Red light: not connected.
Flashing blue: setup mode.
No light: not set up yet.
NAVIGATION MODULE
Please keep clear and do not
cover.
Upward-facing sensor aids
advanced navigation.
DOCK BUTTON
Press to stop cleaning and
send robot back to the
charging base.
EVACUATE & RESUME
Press and hold the DOCK
button for 15 seconds to
turn Evacuate & Resume
ON or OFF.
Turn ON Evacuate & Resume for homes with pets.
Your robot will return to the base to empty the
dustbin after 30 minutes, then resume cleaning
where it left off.
PREPARING YOUR HOME
Your robot uses an array of sensors to navigate around walls, furniture legs, and other obstacles while it
cleans. To prevent the robot from bumping into objects or navigating to areas you don't want it to, use the
included Botboundary strips. For best results, prepare your home as indicated below, and schedule a daily
clean to ensure all floor areas are regularly maintained.
NOTE: Scheduling is one of many features that are only available in the app.
OBSTRUCTIONS
Clear cords and small objects
from floors and open interior
doors to ensure a complete
map of your home.
THRESHOLDS
Your robot may have some
trouble clearing thresholds
higher than an inch. Block
off high thresholds with the
included BotBoundary strips.
STAIRS
Your robot's cliff sensors will
prevent it from falling off
ledges. For the cliff sensors
20cm
Min. to work properly, all runners,
rugs, or carpets must be at
least 20cm from any stairs
(or extend over the edge of
the stairs.)
BOTBOUNDARY STRIPS
PREPPING YOUR HOME USING BOTBOUNDARY STRIPS
Use the BotBoundary strips to quickly and easily create no-go zones to keep your robot out of the areas you
would like it to avoid. These may include:
• Near power cords
• In front of thresholds higher than an inch
USAGE INSTRUCTIONS
1. You can cut BotBoundary strips to shorten
them as needed. (45 cm minimum) If cutting a
strip, make sure it's still long enough to cover
the entire area you need to block off. Gaps may
cause BotBoundary strips to malfunction.
2. Make sure each BotBoundary strip lies
completely flat against the floor, with no
overlapping. NOTE: DO NOT place BotBoundary
strips on top of one another.
3. For best results, place the strips between fixed
objects like furniture legs or door frames, or
make a closed loop around an obstacle.
(18" Minimum)
BotBoundary strip
AVOID MOVING THE
ROBOT OR BASE
While your robot is cleaning,
do not pick it up and move it,
or move the charging base—
this will impact the robot's
ability to map your home.
CHECK BASE FILL LEVEL
During the first few weeks,
your robot will empty more
debris than usual. Check the fill
level regularly. The dustbin is
designed to hold up to 30 days
/ 1 month worth of debris, but
home environments vary, and
the bin may fill up quicker in
some homes.
LIGHTING CONDITIONS
For best results, run your
robot in well-lit conditions. If
you run your robot at night,
keep the lights on in the areas
to be cleaned.
Botboundary strips
FURNITURE DOORWAYS PET BOWLS
BotBoundary strips
s h a r kc l e a n . e u