OcCre 53003 SOLLER Bedienungsanleitung Seite 4

ASSEMBLY INSTRUCTIONS SÓLLER
PHOTO 1. Assemble the single seats using parts 2, 3, 4, 7 and 9 and the double seats, using parts 2, 5, 6, 8 and 9. Mark
equally-separated lines on all of the backrests. Fit and glue the seats to the floor 1 using the template 9. Use quick-drying glue.
Paint the bases black, the floor grey and varnish the wood.
PHOTO 2. Line the exterior side of the partitions 10 using the sheets 11. From the sheets cut out sections approximately the
size of the surface to be covered, glue them into place and then trim off any excess using a cutter. Use contact adhesive.
Varnish them.
PHOTO 3. Tint the interior surface of the partitions and the sides 12 in a sapelli tone and varnish them. Fit, glue and pin these
parts to the platform. Use white glue.
PHOTO 4. Fit and glue the sides 13 and 16 and the fronts 14 and 15 to the interior corners of the platform. Then, onto these
bases, glue the seats 17 and 19 and the backrests 18 and 20. Use white glue. Varnish them.
PHOTO 5. Glue the glass 22, 23 and 25 into the windows 21 and 24. Do the same with the glass 27 in the doors 26. Use
contact glue and varnish them. Glue the handles 28 to both sides of the doors. Paint the parts using the step-by-step photos of
the sample shown on page 7 as a guide. Fit the bars to the inside windows 29 and 30 laving a gap of 5 mm between each bar.
Use quick-drying adhesive. Glue the doors to the frame of the partitions. You can leave them more or less open or closed, as
you prefer.
PHOTO 6. Fit and glue into place the platform sides 31 and fronts 32, 33 and 34. At the top, fit and glue part 35 into place.
Observe the alignment of the holes. Use white glue. Varnish the interior.
PHOTOS 7 to 10. Line the exterior of the tram, using the lining sheets 11. Do the same as with the partitions, cutting out
sections of a similar size to the surface area to be covered and then trimming off the excess with a cutter. Use contact adhesive.
Glue the reinforcements 36 to the doors. Sand down and varnish.
PHOTOS 11 to 13. Glue the parts 37 and 38 (painted the colour of grey) into place and the glass 39 to make up the middle side
windows. Varnish the frames. Glue the middle top windows into place with the grey part at the bottom and on the outside. Then
glue the other middle windows into place with the grey part at the top and on the inside. You can assemble them open or
closed, as you prefer.
PHOTOS 14 to 16. Make up the control panel using the parts 40, 41, 42, 43 and 44. Round off the corners. Use white glue.
Paint it black. Glue the parts 45 and 46 into place. Make a Ø 1.5 mm hole and insert and glue the handle 47, this is done by
flattening one end with a hammer (see close up photo and template). Use quick-drying glue. Paint the auxiliary board 48 black
and the knob on the lever brown. Make up the brake bar with the support 49, in which you have to make a Ø 1 mm hole on one
side in which to insert the stretcher 50, and another Ø 1.5 mm hole on the side in which to insert the steering wheel shaft 51,
attaching the steering wheel 52 to this. On the other side glue the support 53. Use quick-drying glue. Paint the whole assembly
black, including the pedals 54. Fit and glue the control panels, brake bars and pedals onto the fronts of the platform.
PHOTO 17. Varnish the frames 55, 57, 59, 61, 63, 65, 67, 69, 71 and 73 and then glue the glass 56, 58, 60, 62, 64, 66, 68, 70,
72 and 74 to them. Use white glue. Fit and glue each window into place. Use white glue. If you want, on the sloping fronts, you
can leave the windows 65 open, cutting them as shown in the box inset in the photo.
PHOTO 18. Make a Ø 1.5 mm hole in the bar 77, insert the bars 75 into the bars 76, 77 and 78. Insert the vertical bar into the
existing holes in the floor and the roof support and glue each horizontal bar in place as shown in the photo. Use quick-drying
glue. Paint the bars black and varnish the wood.
PHOTOS 19 & 20. Fit and glue the parts 79 to the beams 80. Use white glue. Paint the lights 81 white and brown. Glue the
underside of the roof 82. Varnish and glue the finishes 83, 84, 85 and 86. Glue the lights into place. Fit and glue this assembly
to the passenger platform. Use white glue.
PHOTOS 21 & 22. Pin and glue the strips 87 onto the roof beams and supports. Use white glue. Only insert the pins halfway,
enough so that they keep the strips in place until the glue has set, and then cut off the heads. Once the roof has been lined
sand it down. Glue the finishes 88, 89 and 90 to the exterior edges. Use white glue. Fill any small irregularities and sand down
the surface until it is completely flat. Paint it grey.
PHOTOS 23 & 24. Paint the exterior part of the floor dark orange. Carefully bend the decorations 91 to shape and glue them in
place. Use white glue. Glue on the fenders 92, 93, 94, 95 and 96. Use white glue. Varnish them.
PHOTOS 25 & 26. Fit and glue the carriage springs 98 to the beams 97. Size up the location of the long springs 99 ad make Ø
1.5 mm holes in the beam to insert and glue them in place. Do the same with the hubs beam 100 and glue it into place in the
notches on the beams 97. Fit the hubs 101 into place and then fit and glue the short springs 102 to the hubs beam and part 103.
Use quick-drying glue. Paint the assembly a steel colour. Check the fit of the notches in the platform floor.
PHOTO 27. Glue the parts 104 and 105 to make up the bumper. Paint it black. Paint the front headlights 106 gold and black and
fit the glass 107. Glue these parts into place. Use white glue.
PHOTO 28. Make up the support 109 for the bar 108 of the hooking frame. Glue them to the underside of the bumper. Use
quick-drying glue.