Operation - Makita GF600 Bedienungsanleitung

Inserting the fuel cell
► Fig.8
Push up and pull the fuel cover to open.
► Fig.9: 1. Jet nozzle
Insert the fuel cell directing the jet nozzle of the meter-
ing valve toward the adaptor.
► Fig.10
Insert the jet nozzle into the small hole of the adapter
properly.
► Fig.11
Put the fuel cover over the metering valve and push it
down to latch.
Adjusting the nailing depth
CAUTION:
• Remove the fuel cell, the battery cartridge and
nails before adjusting the depth of nailing.
► Fig.12: 1. Adjuster
To get shallower depth, turn the adjuster to A direction
shown in the figure. To get deeper depth, turn the
adjuster to B direction. Do not turn the adjuster too
much, or the contact element may come off from the
adjuster, or it gets stuck.
Indication lamp
Color of the indication lamp means the followings.
Blinking green: Normal status
Blinking red: Need to recharge the battery cartridge
Lighting-up-red: Recharge the battery cartridge.
Nailing cannot be performed due to no remaining bat-
tery capacity.
Blinking orange: Thoroughly cleaning is recom-
mended. Refer to the section "MAINTENANCE" to
clean inside of the tool thoroughly. To reset the orange
blinking of the indicator lamp, push the contact element
for five seconds, and then push the contact element
five times.
Blinking orange after blinking green and red alter-
nately: Fault detection is running. Remove and reinsert
the battery cartridge to reset. If fault detection is running
again, it is malfunction condition. Ask your local Makita
service center to repair it.
Installing the hook
► Fig.13: 1. Hook
The hook is convenient for temporarily hanging the
tool. You can install it on either side of the tool. It can be
removed without using any tool.
To install the hook, expand the upper part of the hook,
and insert it in the tool. To remove the hook, expand the
upper part of the hook in both directions and pull the
hook from the tool.
ASSEMBLY
CAUTION:
• Always remove the fuel cell and the battery car-
tridge before carrying out any work on the tool.
Loading the nailer
► Fig.14
Insert a strip of nails into the slit in the rear of the magazine.
► Fig.15
Pull the pusher lever with pressing the pusher button all the
way to the rear of the magazine. Then release the pusher but-
ton, and return the pusher lever to the end of the strip gently.
Removing nails
► Fig.16: 1. Pusher button
Pull the pusher lever and push the pusher button to
release the nail supporter, and then return the pusher
lever to the top with pushing the pusher button.
Slide the nails toward the rear of the magazine and
remove them out.
Nose adapter
► Fig.17: 1. Nose adapter
The nose adapter prevents the surface of workpiece from
being scratched or damaged. Place the nose adapter correctly.
Store the nose adapter in place when not in use. The
place for storage is on the bottom sides of the tool.
► Fig.18: 1. Nose adapter
Short nail adapter
► Fig.19: 1. Short nail adapter
► Fig.20: 1. Short nail adapter 2. Bolt
Attach the short nail adapter to prevent the short nails from
being jammed when you use nails shorter than 25 mm (1 ").
Insert the short nail adapter into the slit in the rear of the
magazine. Then fix the adapter by tightening the bolt.

OPERATION

WARNING:
• Do not touch around the exhaust vent. The
surface will be very hot during or after an oper-
ation. Touching around the exhaust vent may
cause burns or injuries.
CAUTION:
• Make sure all safety systems are in working
order before operation.
Checking proper action before operation
Before operation, always check following points.
— Make sure that the tool does not operate only by
installing the battery cartridge and fuel cell.
— Make sure that the tool does not operate only by
pulling the trigger.
— Make sure that the tool does not operate only by
placing the contact element against the workpiece
without pulling the trigger.
— Make sure that the tool does not operate when
pulling the trigger first and then placing the contact
element against the workpiece.
11 ENGLISH