Servicing; Electrical Connection; Special Accessories - Kity 3301415901 Originalanleitung

Pay attention to the safety instructions.
Turn off the motor and pull the plug before servicing or clea-
ning the machine.
All protection and safety devices must be immediately assem-
bled again following repairs and servicing.
1. The assemblage of the circular saw is largely servicefree,
The installed electric motor is completely wired ready for operation.
The customer's connection to the power supply system, and
any extension cables that may be used, must conform with
local regulations.
Motor braking unit
The Kity 415 circular saw bench is fitted with an automatic motor
braking unit which becomes effective as soon as the driving motor is
switched off.
Important remark:
The electric motor is designed for the S 6 / 40 % operating
mode.
Therefore, the motor is automatically switched off in the event
of an overload. The motor can be switched on again after a
cooling down period that can vary.
Defective electrical connection cables
Electrical connection cables often suffer insulation damage.
Possible causes are:
1. Pinch points when connection cables are run through window
D GB
or door gaps.
2. Kinks resulting from incorrect attachment or laying of the con-
nection cable.
3. Cuts resulting from running over the connecting cable.
4. Insulation damage resulting from forcefully pulling out of the
wall socket.
5. Cracks through aging of insulation.
Such defective electrical connection cables must not be used
as the insulation damage makes them extremely hazardous.
Check electrical connection cables regularly for damage. Make sure
the cable is disconnected from the mains when checking.
Electrical connection cables must comply with the regulations appli-
Slide carriage
Plate cutting device
Slide handles
Automatic starter
Riving knife 2,8 mm

Servicing

including the electric motor. Exceptions to this are the normal
wear and tear of the saw blades as well as the bench insert. If
needed, exchange the used bench insert.
2. The bench surface should always be kept resin-free.
3. Keep the saw blade protection box free of wood and chip re-
sidue. When the power plug is pulled, open the protection box
cover and remove any saw dust obstructions.
Electrical connection m
cable in your country.
Single-phase motor
1. The mains voltage must coincide with the voltage specified on
the motor's rating plate.
2. Extension cables up to a length of 25-m must have a cross-
section of 1.5 mm2, and beyond 25 m at least 2.5 mm2.
3. The connection to the mains must be protected with a 16 A
slow-acting fuse.
Three-phase motor
1. The mains voltage must coincide with the voltage specified on
the motor's rating plate.
2. The mains connection and the extension cable must have 5
conductors: 3 phase conductors + 1 neutral conductor + 1 earth
conductor.
3. The extension cable must have a minimum cable crosssection
of 1.5 mm2.
4. The connection to the mains must be protected with a 16 A
slow-acting fuse.
5. The rotating direction must be checked when the machine is
connected to the mains or re-sited. If necessary, the polarity will
have to be changed over (wall socket).
Only a qualified electrician is permitted to connect the machine
and complete repairs on its electrical equipment.
In the event of enquiries please specify the following data:
1. Motor manufacturer
2. Type of current of the motor
3. Data recorded on the machine's rating plate
4. Data recorded on the switch's rating plate
If a motor has to be returned, it must always be dispatched with
the complete driving unit and switch.

Special Accessories

Art. Nr. 7951 0000
Art. Nr. 7961 0000
Art. Nr. 7963 1000
Art. Nr. 7910 4010 Typ ALV 2
Art. Nr. 7910 4020 Typ ALV 10
Art. Nr. 5280 0016 (für Sägeblätter mit 3,2 mm Zahnbreite)
22