Assembly - Kity 3301415901 Originalanleitung

Table height mm
Saw blade diameter min.-max. mm
Width of teeth mm
Suction connector dia. mm
Volume flow m³/h
stat. depression Pa (20m/sec)
Weight kg
Cutting Data
Cutting height at 90° mm
Cutting height at 45° mm
Cutting width at 90° angular cut mm
Saw blade height adjustment mm
Saw blade slewing range
Speed 1/min
Cutting speed m/sec
Parallel cuts width max. mm
Cross cutting jig
Drive
Motor
Input P1 kW
Output P2 kW
Motor speed 1/min
Operating mode
Noise parameters
The noise emission values determined according to EN 23746 for
the sound level and according to EN 31202 (coefficient of correction
k3 calculated according to Appendix A.2 of EN 31204) for the sound
level at the workplace are as follows, based on the working condi-
tions listed in ISO 7904 Appendix A:
Sound level in dB
Idle running L = 90 dB(A)
WA
Operating L = 105 dB(A)
WA
Sound level at the workplace in dB
Idle running L = 77,2 dB(A)
pAeq
Operating L = 89,3 dB(A)
pAeq
For reasons of packaging technology, your Kity machine is not com-
pletely pre-installed.
Put the saw tabletop on the reverse for the installation. Insert a
piece of cardboard to protect the table surface.
Assembly tools
The following tools are included:
2 saw blade keys SW 46/19 and SW 17
For reasons of packaging technology, your Kity machine
is not completely pre-installed.
Put the saw tabletop on the reverse for the installation.
Place a piece of cardboard underneath to protect the table surface.
Installation of the dust suction connector, Fig. 1
1. Mount the dust suction connector on the casing cover.
4 hexagon head cap screws M6 x 10
4 hexagon nuts M6
Installation of the base feet, Fig. 2
1. Hand-tighten all screws and nuts.
2. Each base foot is screwed on the tabletop with 4 hexagon head
cap screws M6x16, 4 serrated lock washers A6,4, and 4 hexa-
230V / 50Hz 400V / 50Hz
2,2 3,0
1,5 2,2
2800
A measurement uncertainty allowance K = 4 dB applies to the men-
tioned emission values.
Dust emission values
The dust emission values measured according to the "Principles for
the inspection of the dust emission (concentration parameters) of
wood working devices" of the Technical Committee Wood are below
2 mg/m3. Thus, a permanently reliable compliance with the TRK
limit value for wood dust valid in the Federal Republic of Germany
can be expected if the machine is connected to a proper operational
aspiration with an air speed of at least 20 m/s.

Assembly

gon nuts M6. The cheese head screw M6 x 40 is fastened with
two nuts on the left side of the frame foot and serves as support
for the sliding stick. The running gear is fastened on the rear
side of the frame feet using two hexagon head cap screws M8
x 16 with nuts and washers. Then put the foot caps on the base
feet.
Installation of the longitudinal and cross struts, Fig. 2
1. Each longitudinal and cross strut is screwed on the tabletop
with 1 hexagon head cap screw M6x16, 1 serrated lock washer
A6,4, and 1 hexagon nut M6.
2. Finally tighten all screws and nuts.
Installation of the switch, Fig. 3
1. Fasten the switch mounting part with 2 hexagon head cap
screws M8x16, 2 washers A8,4, and 2 hexagon nuts M8 on the
tabletop.
19
850
250 - 315
2,8
Ø 100
565
560
53
82
65
260
85
90° - 45°
2760
46 / 56 (60Hz)
345
0° - 60°
400V / 50Hz
4,2
3,0
3400
S6/40%
230V / 60Hz
2,2
1,5
D GB