Safety Instructions; Use Only As Authorized - Kity 3301415901 Originalanleitung

• Please pass on safety notes and instructions to all those
who work on the machine.
• The machine must only be used in technically perfect condi-
tion in accordance with its designated use and the instructions
set out in the operating manual, and only by safety-conscious
persons who are fully aware of the risks involved in operating
the machine. Any functional disorders, especially those affec-
ting the safety of the machine, should therefore be rectified
immediately.
• Only tools which correspond to the European norm, EN 847-1,
may be used.
• Observe all safety instructions and warnings attached to the
machine.
• See to it that safety instructions and wamings attached to ma-
chines are always complete and perfectly legible.
• Caution when working: There is a danger to fingers and hands
from the rotating cutting tool.
• Make sure that the machine stands stable on firm ground.
• Check all power supply lines. Do not use defective lines.
• Keep children away from the machine when it is connected to
the power supply.
• Operating personal must be at least 18 years of age. Trainees
must be at least 16 years of age, but may only operate the
machine under adult supervision.
• Persons working on the machine may not be diverted from
their work.
• The machine must be equipped with a table length extension if
a second person is work.ing at the circular sawbench removing
cut work.pieces. The second person may not stand anywhere
else but at the take-off table end.
• The working space on the machine must be free of chips and
wood scrap.
• Wear only close-fitting clothes. Remove rings, bracelets and
other jewelry.
• Pay attention to the rotational direction of the motor and tool -
see Electrical Connection.
• The safety mechanisms on the machine may not be removed
or rendered unusable.
• Cleaning, changing, calibrating, and setting of the machine
may only be carried out when the motor is switched off. Pull
the power supply plug and wait for the rotating tool to com-
pletely stop.
• Switch the machine off and pull power supply plug when
rectifying any malfunctions.
• The machine must be attached to a Kity dust extractor during
all work. cycles. Please observe the proper use of this.
• When working on the machine, all safety mechanisms and
covers must be mounted.
• Use only sharpened, nick-free and non-deformed saw blades.
• Circular saw blades made from superspeed steel may not be
used.
• The splitting wedge is an important safety feature. The work.
piece is fed through the splitting wedge, which prevents the
cut from closing behind the saw blade and also prevents the
workpiece from kicking back.
• Lower the cover onto the work.piece during every working
operation. It must stand horizontal above the saw blade.
• Always use a push-stick for longitudinal cuts of narrow work
pieces less than 120 mm). The push-stick must be used to
prevent you from having to work. with your hands near the
sawblade. Stop the machine to repair a failure or remove
pieces of wood which have become jammed. Disconnect the
mains plug.
• Switch the machine off and pull power supply plug when
rectifying any malfunctions.
• The table insert must be renewed when the saw slot is wom
Safety instructions m
down. Pull power supply plug.
• Before the machine is put into operation it must be connected
to a dust extractor with a flexible, non-flammable suction hose.
The suction should switch on automatically when the machine
is switched on.
• When leaving the work place, switch the motor off. Pull the
power supply plug.
• Cut off the extemal power supply of the machine or plant even
if only minor changes of place are envisaged. Properly recon-
nect the machine to the supply mains before recommissioning.
• Connection and repair work. on the electrical installation may
be carried out by a qualified electrician only.
• All protection and safety devices must be replaced after com-
pleting repair and maintenance procedures.

Use only as authorized

• The machine corresponds to the valid EC guideline.
• The Kity 415 circular sawbench is defined as a semi-stationary
machine in accordance with pr EN 1870-1.
• To transport the machine, grasp the table firmly at the front and
at the rear using both hands and lift the machine.
• If an original Kity base is not used, the machine must be
placed firmly upon a stable stand resembling a table. The wor-
king height should be 850 mm.
• The machine's workstation is in front of the machine to the left
of the sawblade.
• The machining range and surrounding areas of the machine
must be clear of interfering foreign matter to prevent accidents
occurring.
• Workpieces must be completely free of foreign objects, i.e.
nails or screws.
• Before the machine is put into operation it must be connected
to a dust extractor with a flexible, non-flammable suction hose.
The suction should switch on automatically when the machine
is switched on.
• When used in enclosed rooms, the machine must be connec-
ted to a vacuum exhaust unit. Use the Kity dust extractor
ha 3200 or ha 2600 to remove matchwood or saw dust. The
vacuum support flow rate must be 20 m/s. Subatmospheric
pressure 1200 Pa.
• Do not remove or shut off vacuum exhaust systems or dust
removers while machine tools are operating.
• The Kity circular sawbench is designed exclusively for the
machining of wood and materials similar to wood. Only original
Kity tools and accessories may be used. Use the required
sawblade in accordance with the EN 847-1 norm depending
on the type of cut and type of wood (solid wood, plywood or
chipboard). Please observe the Kity Special Tool Accessories.
• The machine must only be used in technically perfect condi-
tion in accordance with its designated use and the instructions
set out in the operating manual, and only by safety-conscious
persons who are fully aware of the risks involved in operating
the machine. Any functional disorders, especially those affec-
ting the safety of the machine, should therefore be rectified
immediately.
• Relevant accident prevention regulations and other, generally
recognized safety-technical rules must also be adhered to.
The Kity machine may only be used, maintained, and ope-
•
rated by persons familiar with it and instructed in its operation
and procedures. Arbitrary alterations to the machine release
the manufacturer from all responsibility for any resulting dama-
ges.
• The Kity machine may only be used with original accessories
and original tools made by the manufacturer.
• Any other use exceeds authorization. The manufacturer is not
responsible for any damages resulting from unauthorized use;
risk is the sole responsibility of the operator.
17
D GB