Disposal And Recycling; Electrical Connection - HERKULES TKGS1000 Anwenderhandbuch- Originalbetriebsanleitung

• We recommend that you clean the equipment imme-
diately after you use it.
• Clean the equipment regularly with a damp cloth and
some soft soap. Do not use cleaning agents or sol-
vents; these may be aggressive to the plastic parts in
the equipment. Ensure that no water can get into the
interior of the equipment.
• In order to extend the service life of the tool, oil the
rotary parts once monthly. Do not oil the motor.
Brush inspection
In case of excessive sparking, have the carbon brushes
checked only by a qualified electrician. Important. The
carbon brushes should not be replaced by anyone but a
qualified electrician.
10. Transport
Transport (always in table saw mode)
• Move the lower saw blade guard (14) above the saw
guide until you can hear a „click". The front of the
saw blade guard has to be flush with the white line
on the saw guide.
• Position the saw button downwards by pressing the
unlocking button (2) on the saw head and activating
the lock pin (20).
• Put the rip fence (1) on the saw blade guard and
attach it.
• Lift the machine by holding it on both sides of the
lower frame (6).
m WARNING
There is a risk of injury in the event of improper han-
dling of the machine, during lifting or turning.
Always disconnect the mains supply before eve-
ry transport
Only ever transport the saw in table mode and with
the rip fence mounted on the saw blade. This will pre-
vent injury from the saw blade. Never transport the
machine by its safety equipment (e.g. safety guard,
riving knife).
11. Storage
Store the machine and its accessories in a dark, dry
and frost-free place, inaccessible to children. The
ideal storage temperature is between 5 and 30˚C.
Store the power tool in its original packaging.
Cover the power tool to protect it from dust and hu-
midity.
Keep the operating manual with the power tool.

12. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions.
The customer's mains connection as well as the
extension cable used must also comply with these
regulations.
• Given unfavorable conditions in the power supply the
product can cause the voltage to fluctuate temporarily.
• The product is exclusively intended for use at con-
nection points that have a continuous current-carry-
ing capacity of at least 100 Amper phase.
• As the user, you are required to ensure, in consulta-
tion with your electric power company if necessary,
that the connection point at which you wish to ope-
rate the product meets the specified requirements.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the mo-
tor can be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage regu-
larly. Make sure that the connection cable does not hang
on the power network during the inspection.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connection
cables with the marking „H05VV-F".
The printing of the type designation on the connection
cable is mandatory.
AC motor
• The mains voltage must be 230 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event of
any enquiries:
Type of current for the motor
• Machine data - type plate
• Machine data - type plate

13. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to the
raw material system. The unit and its accessories are
made of various types of material, such as metal and
plastic. Defective components must be disposed of
as special waste. Ask your dealer or your local coun-
cil.
31 І 76
.
2