Remaining Risks; Technical Data - HERKULES TKGS1000 Anwenderhandbuch- Originalbetriebsanleitung

rings which are suitable for the intended purpose
specified by the manufacturer;
• If the machine is equipped with a laser, this laser
must not be replaced by a laser of another type.
Repairs must be carried out by the laser manu-
facturer or an authorised representative;
• Ensure that the upper part of the saw blade is
completely enclosed when in mitre saw mode;
• Replacement and alignment of the saw blade
have to be carried out properly;
• Make sure that the machine, if possible, is se-
cured to a work bench or a table.
• Do not remove offcuts or other work piece parts
from the cutting area while the machine is run-
ning and the blade has not yet come to a stand-
still;
• In the table circular saw mode, use a riving knife
and set it up properly; (Fig. 20)
• The machine must not be used for slotting (insert
grooves);
• During transport, the upper part of the saw blade
must be covered, e.g. by the upper guard, or the
saw blade must be in its lowest position;
• In the table circular saw mode, the lower saw
safety device must be used and set up properly.
m WARNING
• The vibration levels during operation of the pow-
er tool can deviate from the specified vibration
levels, depending on the application of the power
tool.
m WARNING
• Restrict the work time and reduce the actual op-
erating time to lower the risk of vibration.

Remaining risks

The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use of
improper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instruc-
tions" and the „Proper use" are observed along with
the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the machine
in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Hands may never enter the processing zone when the
machine is in operation. Release the handle button
and switch off the machine prior to any operations.
• Prior to any adjustment, maintenance or service work
disconnect the mains power plug!
The following factors affect noise emission:
1. material to be cut
2. type of saw blade
3. feed force
The following factors affect dust development:
1. worn saw blades
2. dust extraction units with an air speed of less than
20 m/s
3. work piece not guided properly
Working on particular timber such as beech and MDF
can cause dangerous dust during sawing.
Therefore, a dust extraction unit must be used.

6. Technical Data

AC motor
Performance
Idle speed n
0
Carbide saw blade
Number of teeth
Extraction connection
Table saw:
Saw table
Cutting height
Riving knife thickness
Cross stop and rip fence
Chop saw
Angular range
Mitre cut
Saw table
Saw width x saw depth
at 90°
Saw width x saw depth
at 45°
Saw width x saw depth at
2 x 45° (double mitre cut)
Protection rating
Weight
Subject to technical changes!
* operating mode S6 25%: Continuous operation with
intermittent loading (playing time 10 min).
Engine protection of to hot warming up:
It´s allowed to run the engine with nominal power maxi-
mum 25% of playing time. After this the machine must
run 75% of playing time steadily without load.
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure L
pA
Sound power L = 105.5 dB(A)
wA
Measurement uncertainty KpA = 3.0 dB(A)
Use hearing protection.
Noise at the work place can exceed 85 db (A). In this
case, sound protection measures are required for
the user. Being subjected to noise can cause hear-
ing loss. The overall vibration values (vector sum of
three directions) have been determined according to
EN 61029
27 І 76
220 - 240 V ~ 50Hz
S1 1600 Watt
S6 25%* 1800 Watt
5000 min
ø 254 x ø 30 x 3mm
32 mm
432 x 298 mm
0-46 mm
2,5 mm
rotatable
-60° to + 60°
-50° / 0°/ +60°
0° to 45° to the left
460 x 335 mm
110 x 70 mm
70 x 70 mm
60 x 35 mm
approx. 19 kg
= 92.5 dB(A)
-1
60
II