Technical Data; Before Starting The Equipment - PrimAster KZS1500 Original Bedienungsanleitung

6. Technical data

AC motor
Power
Operating mode
Idle speed n
0
Carbide saw blade
Number of teeth
Swivel range
Mitre cut
Saw width at 90°
Saw width at 45°
Saw width at 2 x 45°
(double mitre cut)
Protection class
Weight
Laser class
Wave length of laser
Laser output
Laser module power
supply
* S6, continuous operation periodic duty.
Identical duty cycles with a period at load fol-
lowed by a period at no load. Running time 10
minutes; duty cycle is 25% of the running time.
The work piece must have a minimum height of
3mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
Noise and vibration
Total noise values determined in accordance with
EN 61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Vibration emission value a
Uncertainty K
220 - 240 V ~ 50Hz
1200 Watt
S6 25%* 1500W
5000 min
-1
ø 210 x ø 30 x 2,6 mm
24
-45° / 0°/ +45°
0° bis 45° nach links
340 x 58 mm
240 x 58 mm
240 x 32 mm
II
approx. 13 kg
2
650 nm
< 1 mW
2 x 1,5 V Micro (AAA)
99.6 dB(A)
3 dB
112.6 dB(A)
3 dB
≤ 2.5 m/s²
h
1.5 m/s²
The specified vibration emission value has been
measured according to a standardised test proce-
dure and can be used in comparison with another
power tool.
The specified vibration emission value can also be
used for an initial assessment of the exposure.
Warning:
The vibration emission value can vary from the spec-
ified value during actual use of the power tool, de-
pending on the way it is used. Try to keep exposure
to vibrations as low as possible. Measures to reduce
exposure to vibration are, for example, wearing
gloves when using the machine, or by reducing the
work time. All parts of the operating cycle must be
considered for this (for example: times during which
the power tool is switched off and times when it is
turned off but runs without load).
Residual risks
The machine has been built according to the
state of the art and the recognised technical
safety requirements. However, individual residu-
al risks can arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed
along with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must al-
ways be fixed between the clamps.
• Avoid accidental starting of the machine: the op-
erating button may not be pressed when inserting
the plug in an outlet.
• Use the tool that is recommended in this manual.
In doing so, your mitre saw provides optimal per-
formance.
• Hands may never enter the processing zone when
the machine is in operation.
• Release the handle button and switch off the ma-
chine prior to any operations.

7. Before starting the equipment

• The equipment must be set up where it can stand
securely. Secure the machine on a workbench or a
stand with 4 screws through the holes in the fixed
saw table (15).
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
GB | 27