Dmx Linking; Usb Software Update - Chauvet Ovation REVE E-3 Kurzanleitung

AC Power
This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.
Power Linking
It is possible to link up to 3 Ovation Rêve E-3 products at 100 V, 4 products at 120 V, 7 products at 208 V, 8 products at
230 V, or 8 products at 240 V. Never exceed this number. Power-linking cords can be purchased separately.
AC Plug
Connection
AC Live
AC Neutral
AC Ground
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Replacing the Fuse
1. Disconnect this product from power.
2. Using a Phillips-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect power.

DMX Linking

The Ovation Rêve E-3 will work with a DMX controller using a 3- and 5-pin DMX serial connection. A DMX Primer is
available from www.chauvetprofessional.com.
DMX Connection
The Ovation Rêve E-3 uses a 3- and 5-pin DMX data connection for its DMX personalities: 1Ch, 5Ch, 6Ch, 8Ch, 12Ch,
14Ch1, 14Ch2, 18Ch, and HSV. See the User Manual for information about connecting and configuring the product for
DMX operation.
Master/Slave Connection
The Ovation Rêve E-3 uses the DMX data connection for its master/slave mode. See the User Manual for information
about how to connect and configure the product for master/slave operation.
RDM (Remote Device Management)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally
along existing DMX cabling. Check with the manufacturer or the DMX controller's User Manual, as not all DMX controllers
have this capability. The Ovation Rêve E-3 supports RDM protocol that allows feedback to make changes to menu map
options. Download the User Manual from

USB Software Update

The Ovation Rêve E-3 allows for software update through USB using the built-in USB port. To update the software using
USB flash drive, do the following:
1. Power on the fixture and plug the flash drive into the USB port.
2. Once the flash drive has been detected, the message "Upgrade Firmware" will be displayed. Press ENTER. If a
different message appears on the display, search for the updated software in the Menu (Updated Firmware). A
list of the updated software files will be displayed.
3. Select the file that needs to be uploaded. The message "Are you sure?" will be displayed. Press ENTER.
4. If the selected file is correct, the upgrade will be completed. Restart the fixture. If the selected file is incorrect, the
upgrade will fail, and the display will go back to the main interface. Repeat steps 1-3 using the correct file.
The .chl format file needs to be placed in the OVATION folder in the USB flash drive.
Lens Tubes
The following lens tubes are available for purchase:
• 19°, 26°, 36°, and 50° with gel frame (6.25 in/159 mm accessories)
• 5° zoom gel frame (14 in/356 mm)
• 10° zoom gel frame (12 in/304 mm)
• 14°, 15–30° and 25°–50° zoom gel frame (7.5 in/191 mm accessories)
Ovation Rêve E-3 QRG Rev. 1
QUICK REFERENCE GUIDE
Wire (U.S.)
Black
White
Green/Yellow
www.chauvetprofessional.com
Wire (Europe)
Brown
Blue
Green/Yellow
for more details.
EN
Screw Color
Yellow/Brass
Silver
Green
2