Volume Adjustment - THOMSON MIC215i Bedienungsanleitung

USING
TImER SETTING
The timer function can turn the unit on at a preset time.
To set timer
• In standby mode, press and hold
the EQ/TImER button on the remote
control until the hour digits and TImER
indicator blink.
• Tap the 7 or 8 buttons to adjust to the desired hours
then tap the EQ/TImER button once to confirm. The
minute digits will begin to blink.
• Tap the 7 or 8 buttons to adjust to the desired
minutes then tap the EQ/TImER button once to
confirm.
• Press the FuNCTION button to select the timer mode
(Radio, iPhone or CD). The "RAd", "iPhn" or "cd" icon
will be shown on the display. Tap the EQ/TImER button
once to confirm.
• For RADIO timer, tune in to a desired station.
• For CD timer, insert a CD into the unit.
• For iPod timer, insert your iPod/iPhone into the
connector.
• Press the vOlumE -/+ buttons to adjust the volume
levels.
• Press the EQ/TImER button to confirm. The timer
indicator will stop blinking and remain on.
• The unit will wake up to "RADIO", "iPod" or "CD" when
the timer reaches the preset time. If no disc is inserted
or no iPod/iPhone is installed, the unit will jump to radio
mode automatically.
Note:
• After the unit wakes up, you can adjust the volume
control to obtain the desired volume. Press the q
button once to shut off the timer (timer setting will stay
active; it will turn on again, 24 hours later the time that
the timer is set to).
• If timer is set for FM tuner, it will wake up to the last
station you tuned in.
To cancel timer
• Press and hold the EQ/TImER button on the remote
control until the TImER indicator goes out.
SlEEP TImER SETTING
The sleep timer can automatically turn the unit off after a
certain time.
• While the unit is on, press the SlEEP button, "00" will
appear on the display.
• Press the SlEEP button repeatedly to select the
desired sleep time as below:
• After setting a desired sleep time, the unit will
automatically turn off once it counts down the sleep
time.
• To clear the preset sleep time, press the SlEEP button
until "00" appears.
EN 16
MICRO SYSTEM
MIC215i

vOlumE ADJuSTmENT

To Adjust the volume
Adjust the vOlumE levels to obtain the desired volume.
Note: Press the button to turn off the sound and
the volume numbers will blink on the display. Press the
button again or press the vOlumE -/+ buttons to resume
the voice.
lISTENING TO THE RADIO
• Press the q button to turn the unit on.
• Press the FuNCTION button to switch
to RADIO mode (only FM band is
available).
• Press the 7 or 8 button to tune in to
a station.
• Adjust the volume levels.
Searching for a Station Automatically
• Press and hold the 7 or 8 buttons until the tuner
starts searching for a station, then release. After tuning
in a station, the search stops.
• The search may not stop at a station with a very weak
signal.
Presetting Stations
The unit can store a total of 20 stations in memory.
Presetting allows you to tune in to a station directly.
• Tune in to a desired station.
• Press the mEm/ button. The "mEmORY" indicator
will appear and preset number will blink on the display.
• Press the mEm.uP/ button if you wish to store to a
different preset number.
• Press the mEm/ button again to store it in memory.
• Repeat the above steps to store other stations.
Tuning in to a Preset Station
• Press the mEm.uP/ button to select a preset
station.
For Better reception
Fully unwind the antenna wire. Extend the antenna wire and
place it in the position that sounds best.
Note:
• When the reception is good, the "((STEREO))" indicator
will appear on the display.
• Do not connect the FM antenna to an outside antenna.