Operation - Husqvarna LB 442i Bedienungsanweisung

Introduction
WARNING:
product, you must read and understand the
safety chapter.
Husqvarna Connect
Husqvarna Connect is a free app for your mobile device.
The Husqvarna Connect app gives extended functions
for your Husqvarna product:
• Extended product information.
• Information about, and help with, product parts and
servicing.
To start to use Husqvarna Connect
1. Download the Husqvarna Connect app on your
mobile device.
2. Register in the Husqvarna Connect app.
3. Do the instruction steps in the Husqvarna Connect
app to connect and register the product.
Husqvarna Fleet Services
Husqvarna Fleet Services
the operator an overview of all products that are
connected. On this product a Husqvarna Fleet
™
Services sensor can be installed. The Husqvarna Fleet
™
Services sensor collects product data and lets you
connect to the Husqvarna Fleet Services
Husqvarna Fleet Services
operation time, servicing intervals and location of the
product.
For more information about Husqvarna Fleet Services
download the Husqvarna Fleet Services
to your Husqvarna representative.
To prepare the sensor (accessory)
1. Use the sensor key to open the lid of the sensor.
(Fig. 22)
2. Remove the sensor.
3. Connect the battery to the sensor. The LED light of
the sensor comes on. (Fig. 23)
4. Download the Husqvarna Fleet Services
5. Log on to the Husqvarna Fleet Services
6. Do a pairing operation. Refer to
operation between the app and the product on page
16
To do a pairing operation between the app
and the product
1. Log on to the Husqvarna Fleet Services
16
Before you operate the
™
™
is a cloud solution that gives
™
system. The
™
system reports data such as
™
app or speak
™
app.
™
app.
To do a pairing
™
app.

Operation

2. Select your product in the app.
3. Scan the code behind the sensor with your mobile
device to install the sensor in the app.
Note:
It is only necessary to do a pairing operation
between the app and the product one time.
To install the sensor
1. Make sure that the sensor is connected to the
Husqvarna Fleet Services
pairing operation between the app and the product
on page 16 .
2. Drill 2 holes by the marks in the enclosure slot. (Fig.
24)
Note:
Make sure that the holes are the same
dimension as the rivets supplied with the sensor.
3. Use a pair of pliers to remove the outer holes on the
sensor slot. (Fig. 25)
4. Drill 2 holes by the marks in the sensor slot. (Fig. 26)
5. Align the sensor slot with the enclosure slot. (Fig. 27)
6. Attach the sensor slot with the rivets.
7. Install the sensor in the sensor slot. Align the white
mark on the sensor with the mark on the sensor slot.
(Fig. 28)
8. Close the lid to the sensor and lock it with the sensor
key. Make sure that the top of the Husqvarna "H"
points away from the safety key. (Fig. 29)
To set the cutting height
The cutting height can be adjusted in 4 levels for LB
™ 442i. The cutting height can be adjusted in 6 levels for
,
LB 448i.
1. Push the cutting height control in the direction of the
wheel and then rearward to increase the cutting
height.
2. Push the cutting height control in the direction of the
wheel and then forward to decrease the cutting
height. (Fig. 30)
CAUTION:
too low. The blades can hit the ground if the
surface of the lawn is not level.
Battery
WARNING:
you must read and understand the safety
chapter. You must also read and understand
the operator's manual for the battery and the
battery charger.
™ To do a
app. Refer to
Do not set the cutting height
Before you use the battery,
1520 - 002 - 09.11.2020